Maximum lift height (A) | 2284 mm / 90 in. |
Clearance at full height - bucket dumped (C) | 1743 mm / 68.6 in. |
Dump angle, degrees (E) | 43 degree (angle) |
Rollback angle, degrees (G) | 25 degree (angle) |
*Inventory shortages may cause extended delivery dates
*This price does not include attachments and accesories
Maximum lift height (A) | 2284 mm / 90 in. |
Clearance at full height - bucket dumped (C) | 1743 mm / 68.6 in. |
Dump angle, degrees (E) | 43 degree (angle) |
Rollback angle, degrees (G) | 25 degree (angle) |
*Inventory shortages may cause extended delivery dates
*This price does not include attachments and accesories
All pivot points on the loader have grease fittings that are accessible from the side of the loader to make greasing the loader much easier, ensuring that all grease points are more likely to be serviced. No more searching for grease points that are hard to find. Removing the grease gun from the grease fitting or zerk is not a problem either as sufficient radius has been left to allow the grease gun tip to be rotated to the side for removal from the fitting or zerk.
The H-Series Loaders are designed for easy removal and mounting to and from the tractor without tools.
The parking stand, attached to the front frame of the tractor, is an integral part of the loader during loader operation.
The parking stand lowers into position by moving the joystick to the raised position once the latches are opened. This allows the loader to move to the parked position.
To view a video of how the Quik-Park© system works click here.
NOTE: This video only shows the dismount and mount of the loader without disconnecting the hydraulics. To completely remove the loader, the operator must turn the tractor off, relieve the hydraulics, and then disconnect the hoses from the couplers.
Key Specs | |
Maximum lift height (A) | 2284 mm 90 in. |
Loader | |
Lift capacity at full height | Measured at pivot (U) 617 kgf 1360 lbf Measured at 500 mm ahead of pivot (V) 453 kgf 999 lbf |
Boom breakout force | Measured at pivot (Y) 1295 kgf 2855 lbf Measured at 500 mm ahead of pivot (Z) 922 kgf 2032 lbf |
Bucket rollback force capacity | At maximum height (VV) 1205 kgf 2657 lbf At 59-in. (1500-mm) lift height (XX) 1518 kgf 3347 lbf At ground-level line (ZZ) 1188 kgf 2619 lbf |
Key Specs | |
Clearance at full height - bucket dumped (C) | 1743 mm 68.6 in. |
Dump angle, degrees (E) | 43 degree (angle) |
Rollback angle, degrees (G) | 25 degree (angle) |
Tractor | |
Model | 3120/3320/3520/3720 |
Front tire | 7.00-14 6PR R1 |
Rear tire | 11.2-24 6PR R1 |
Wheelbase | 1727 mm 68 in. |
Pump capacity | 8.6 gpm |
Rated pressure | 2500 psi |
Loader | |
Base weight | 257.21 kg |
Bucket weight | 93.8 kg 206.8 lb |
Lift capacity at 59 in. (1500 mm) | Measured at pivot (W) 771 kgf 1700 lbf Measured at 500 mm ahead of pivot (X) 595 kgf 1312 lbf |
Dimensions | Maximum lift height (A) 2284 mm 90 in. At full height - bucket level(B) 83.5 in. 2123 mm At full height - bucket dumped (C) 1743 mm 68.6 in. |
Overall length (I+F), ft (m) | 3.122 m 10.24 ft |
Digging depth (H) | 76 mm 2.9 in. |
Reach | At maximum height (D) 773 mm 30.4 in. At ground level - bucket level (F) 1381 mm 54.4 in. |
Bucket angle | Dump angle, degrees (E) 43 degree (angle) Rollback angle, degrees (G) 25 degree (angle) |
Cycle times | Loader raise, seconds 2.76 seconds Loader lower, seconds 1.69 seconds Bucket dump, seconds 2.91 seconds Bucket rollback, seconds 1.72 seconds |
Ballast box can be used to carry additional ballast for greater tractor stability.
A 23-cm (9-in.) high extension can be added to ballast box for even greater capacity.
The hitch utilizes a standard Category 1 configuration for connection to the tractor Category 1 hitch.
A bushing kit is required for the ballast box to be used with the iMatch™ Quick-Hitch.
Materials buckets are available to match tractor-loader applications. The buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks. The top surface of the bucket is parallel to the cutting edge, which aids the operator as a leveling guide.
There is a quik-change connection for easy on/off.
When the 220R Loader is ordered factory installed on model year 2017 2R Tractors, the 1450-mm (57-in.) materials bucket is base equipment.
For non-model year 2017 2R Tractors, the bucket and other specific configuration items will need to be ordered through Parts (such as mounting frames, and hood guard).
Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.
Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.
Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.
Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.
Materials buckets are available to match tractor-loader applications. The buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks.
IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier use applications, use heavy-duty bucket.
The top surface of the bucket is parallel to the cutting edge, which aids the operator as a leveling guide.
There is a quik-change connection for easy on and off.
The round-back design helps material flow when filling or dumping the bucket.
Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.
Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.
Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.
Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.
Materials buckets are available to match tractor and loader applications. May be used for loading dirt, gravel, feed and light materials, as well as scrapping, digging and other general purpose tasks.
IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier-use applications, use the heavy-duty bucket.
Top surface of the bucket is parallel to cutting edge, which aids operator as a leveling guide.
Quik-Change connection for easy on and off.
Round-back design helps material flow when filling or dumping the bucket.
Recommended for heavier use applications, such as commercial operations and rental customers.
Additional strength is added to the cutting edge and the replaceable cutting edge is reversible for longer wear life.
Not compatible with tooth bars.
NOTE: Heavy-duty buckets come standard with the holes to install the replaceable cutting edge. Standard materials buckets require installation of attaching holes.
Recommended for heavier-use applications, such as commercial operations and rental customers. Additional strength is added to the cutting edge. Replaceable and reversible cutting edge for longer wear life.
Hood guard attachment to make BW15219 or BW15221 into a deluxe hood guard.
A hood guard can be ordered for a tractor without ordering a loader.
The hood guard protects the front of the tractor while operating the loader.
The bolt-on design stays with tractor when loader is removed.
A hood guard can be ordered for a tractor without ordering a loader.
The hood guard protects the front of the tractor while operating the loader.
The bolt-on design stays with tractor when loader is removed.
A hood guard can be ordered for a tractor without ordering a loader.
The hood guard protects the front of the tractor while operating the loader.
The bolt-on design stays with tractor when loader is removed.
The hood guard for the 3000 TWENTY Series Tractors pivots forward to allow the tractor hood to be raised.
A hood guard can be ordered for a tractor without ordering a loader.
The hood guard protects the front of the tractor while operating the loader.
The bolt-on design stays with tractor when loader is removed.
Hood guard attachment to make BW15219 or BW15221 into a deluxe hood guard.
Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.
Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.
Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.