John Deere 7500A

Feature Overview
John Deere 7500A
  • TechControl™ Display locks in performance, and uptime
  • Set mowing turn speed to reduce scuffing
  • AutoPedal™ lowers fuel consumption and noise
  • Proven hybrid design eliminates hydraulics from reel circuit
Feature Overview
John Deere 7500A
  • TechControl™ Display locks in performance, and uptime
  • Set mowing turn speed to reduce scuffing
  • AutoPedal™ lowers fuel consumption and noise
  • Proven hybrid design eliminates hydraulics from reel circuit
We are here to help
Features

Electric reel drive system eliminates all potential leak points in the reel circuit

Electric motors drive cutting units Electric motors drive cutting units
#

Ninety percent of all hydraulic leaks occur in the reel hydraulic circuit, mainly due to the necessity of having flexible hoses extending from the front of the machine for the front reels.

 

These hoses see a lot of flexing during the mowing day as cutting units are raised and lowered. Cutting units also steer and float to follow undulations, increasing fatigue for the reel motor hoses.

 

The 6080A, 6500A, 7500A, and 8000A E-Cut© Hybrid Fairway Mowers have eliminated all reel circuit leak points by removing all hydraulics from the cutting unit drive circuit.

 

This has eliminated the following hydraulic components:

  • Reel drive section of hydraulic triple pump
  • Hydraulic reel motors
  • Backlapping valve
  • Flexible hoses
  • Fittings
  • Hard lines

Fewer hydraulic components leads to fewer leaks, increasing confidence that the finely manicured turf will not be damaged by hot hydraulic oil spilled onto a playing surface before an important tournament. 


Steering cylinder and linkage systemSteering cylinder and linkage system

Ever wanted stripes in the fairways as straight as they are on the greens? The A-Model PrecisionCut© and E-Cut© Hybrid Fairway Mowers do exactly that. Utilizing the same style steering cylinder as on the 2500B PrecisionCut and 2500E E-Cut Hybrid Riding Greens Mowers, the PrecisionCut and E-Cut Hybrid Fairway Mowers can mow the straightest lines of any mower in the industry today.

Traditional hydraulic cylinders have a rod on only one side of the cylinder. The cylinder on the A-models has one rod that goes through both sides of the cylinder. This equalizes volume and pressure on both sides of the cylinder packing, helping the operator make perfectly straight lines with little effort.

This system also equalizes the steering effort, meaning easy turns whether turning to the right or to the left.


Grooved disc rollerGrooved disc roller

The grooved disc roller can be used with 55.9-cm (22-in.) Quick-Adjust 5 (QA5) cutting units, in combination with the GTC and FTC, to provide additional roller options for fairway, tees, and approach areas.

 

The increased diameter improves the durability over smaller rollers and it features hardened discs for improved wear which retains spring tension for reduced maintenance, making it an ideal roller for fairway, tee, and approach mowing.


48-V 180-amp 48-V 180-amp
#

The reel circuit is powered by a 48-V, 180-amp alternator belt-driven by the engine. The alternator supplies constant power to the reel circuit and only generates 48 V when the mow system is engaged.

 

Due to this design, no additional batteries are required to drive the reel motors on the 6080A, 6500A, 7500A, and 8000A E-Cut© Hybrid Fairway Mowers. With traditional electrical mowing systems, the frequency of clip would change as the batteries drained while mowing.

 

A battery pack begins to lose its power immediately when used, but not on the E-Cut Hybrids. Since they still use an engine to drive an alternator, the frequency of clip at the start of the day and at the end of the day is exactly the same, yielding unparalleled quality of cut from start to finish.

 

Plus, the machine doesn't have to be plugged in to charge the batteries once the day's mowing is done.  The only limitation on run time with the E-Cut Hybrids is making sure the operator starts the day with a full fuel tank, just like with any other gas- or diesel-powered machine on the market today.

 

The alternator only supplies power to the reel circuit. The remainder of the circuits are powered by a 12-V battery.


Front tire Front tire

When considering a fairway mower's effects on turf compaction, there is more to it than just weight alone. Weight is only a small factor in determining turf compaction.

A key component is the selection of tires used on the machine involves both sizing and tread patterns. The John Deere PrecisionCut© and E-Cut© Hybrid Fairway Mowers use large, 26x14-12 front tires for proper front weight distribution, and 20x10-8 tires in the rear to distribute the rear weight.

Both tires use a turf tread to maximize turf friendliness.

They excel in weight distribution providing low ground pressure onto the turf. This provides less tracking, less marking, and less compaction.


MTSpiral roller overall MTSpiral roller overall
MTSpiral end section MTSpiral end section

The MTSpiral roller and the MTGrooved roller (not shown) options are available for Quick-Adjust 5 (QA5) cutting units to minimize roller overlap marks.

 

The MTSpiral roller and the MTGrooved roller options take the patented 50.8-mm (2-in.) machine spiral roller to a whole new level. These designs reduce the number of times the grass is rolled in the overlap area of the cutting units. With these unique designs, the material in the overlap of the roller is machined down to a smaller diameter, allowing the ends of the rear cutting unit rollers to roll through the open space of the front cutting unit rollers.

Types of overlap marks and what causes them
Cause of roller overlap marks Cause of roller overlap marks
Roller overlap marks - bentgrass fairway Roller overlap marks - bentgrass fairway

There are two types of overlap marks: reel overlap marks and roller overlap marks. It can often be difficult to determine what type of overlap marks a customer may be experiencing. In general, a roller overlap mark is roughly 88.9-mm (3.5-in.) to 101.6-mm (4-in.) wide, while a reel overlap tends to be 63.5-mm (2.5-in.) to 76.2-mm (3-in.) wide.

 

A reel overlap mark may be caused by a variety of factors:

  • Bedknife attitude
  • Low effective height of cut
  • Frequency of clip to high (shorter distance between cuts)
  • Cutting unit not parallel
  • Bedknife to reel contact
  • Dull reel and/or bedknife
  • Turf stress

 

A roller overlap mark is caused by how many times the front and rear rollers of the cutting units go over the turf. With traditional roller setups, the grass is rolled four times in the overlap of the front and rear cutting units ™ once by the front roller of the front cutting unit, once by the rear roller of the front cutting unit, once by the front roller of the rear cutting unit, and once by the rear roller of the rear cutting unit.

 

The rest of the cutting unit roller surface, not in the overlap, rolls the grass twice, once by the front roller and once by the rear roller. In certain conditions, particularly in times of lush growth, this may result in overlap marks, which will be darker striping marks in the dark stripes and lighter striping marks in the light stripes.

How the MTSpiral roller and the MTGrooved roller minimize roller overlap marks
Overlap design of MTSpiral rollers Overlap design of MTSpiral rollers
Reduction of overlap marks - bentgrass fairway Reduction of overlap marks - bentgrass fairway

The MTSpiral roller and the MTGrooved roller change the game in terms of roller overlap marks. Due to their design, at no point is the grass rolled more than twice. At every point across all five cutting units, the grass is rolled exactly two times. What this means is a more uniform appearance across the cutting pass.

 

If a customer decides the MTSpiral roller or the MTGrooved roller is the right choice to meet the needs for their application, it is recommended that both front and rear rollers be replaced with the MTSpiral rollers, or MTGrooved rollers, to achieve optimum performance and minimize overlap marks.

 

Since these are spiral and grooved rollers, they will tend to engage the turf more than a cutting unit setup with a smooth rear roller. A starting guideline is that all cutting units equipped with front and rear MTSpiral rollers, or MTGrooved rollers, be set up with a benchsetting of at least 1.1 mm (0.05 in.) higher to achieve a similar effective height of cut. Proper height-of-cut setting is critical for this setup.

 

The optional MTSpiral roller or MTGrooved roller setup does not solve issues due to reel overlap marks. Height-of-cut when the MTSpiral roller or MTGrooved roller is used should be measured by placing the gauge bar approximately 101 mm (4 in.) from the end of the roller to stay away from the tapered ends.

Applications for the MTSpiral roller and the MTGrooved roller
Reduction of overlap marks - paspalum fairway Reduction of overlap marks - paspalum fairway

MTSpiral rollers and MTGrooved rollers can be installed on all PrecisionCut© and E-Cut© Hybrid Fairway Mowers and Riding Greens Mowers with QA5 cutting units. They are an addition to the lineup of roller options for fairway, tee, and approach applications, and may help reduce roller overlap marks on both warm season and cool season turfgrasses. Use of the MTSpiral Rollers or MTGrooved rollers is not recommended for greens applications.

 

Available for both the 45.7-cm (18-in.) and 55.9-cm (22-in.) cutting units, the MTSpiral roller and MTGrooved roller feature a true 45.7-cm (18-in.) and 55.9-cm (22-in.) length with tapered ends. This full-length roller, as compared to other shorter rollers in the marketplace, supports the cutting unit in turns and on sidehills without the gouging or marking.

 

This design is only available in the 50.8-mm (2-in.) configuration at this time:

  • BM23566 ™ 5.1-cm x 55.9- cm (2-in. x 22-in.) MTSpiral roller
  • BM23567 ™ 5.1-cm x 45.7-cm (2-in. x 18-in.) MTSpiral roller
  • BTC10267 - 5.1-cm x 55.9-cm (2-in. x 22-in.) MTGrooved roller
  • BTC10281 - 5.1-cm x 45.7-cm (2-in. x 18-in.) MTGrooved roller

Reel motors Reel motors

The electric reel motors on the 6080A, 6500A, 7500A, and 8000A  E-Cut© Hybrid Fairway Mowers are brushless, allowing them to be compact in size, roughly equal to that of today's hydraulic reel motors. The brushless motors are very efficient, leading to years of optimal performance with very minimal maintenance, and sealed for protection from the elements.

The motors are bidirectional and variable speed, meaning they can spin forward or reverse and at a range of rotational speeds. The motors spin forward for mowing operations and backward for backlapping operations.

 

A poly-chain belt connects the motor shaft to the reel and rotates the reel when the cutting units are engaged. The internal components of the motor are sealed for long life, durability, and protection from the elements.

 

Cutting units are easily removed from the cutting unit motors by loosening the two bolts securing the motor to the cutting unit, turning the motor approximately a quarter turn, and pulling the motor from the cutting unit. This can be done in a matter of seconds. A tether prevents damage to the wiring harness when the motor is removed.


AutoPedal AutoPedal
#

The AutoPedal feature controls engine rpm and transport speed of the machine through the eHydro© foot pedal controls. AutoPedal is similar to an automobile gas pedal operation; the more the forward pedal is pressed, the faster the machine moves and the higher the engine rpm; pressing the pedal less, the slower the machine moves and the lower the engine rpm.

 

On conventional machines, the engine rpm is controlled by the operator by means of a manual or electric/manual throttle. Operators are trained to always operate the engine at wide-open throttle. Running at wide open throttle means running the engine at its fastest speed, which increases the sound levels and fuel usage.

 

The AutoPedal system allows the engine to only run as fast as needed, meaning that as operators transport around the course, the engine speed is only as fast as needed for the transport speed. If the operator approaches play and stops, the engine rpm goes to idle. This makes transporting quieter and since the engine does not run full speed all the time, it reduces fuel consumption.

 

Once the operator reaches the mowing site, engages the mow switch on the CommandARM© controls, the engine rpm automatically increases to full throttle for mowing.


Easy access for cleaning Easy access for cleaning

Easier daily maintenance points are designed into the machine to assist operators with complete daily maintenance and to keep the machine running at peak performance, saving valuable time and money.

 

For ease of service, all daily engine checks are easily accessible by raising the hood. These service points include an engine-oil level check, a coolant level check, hydraulic fluid level, and an air-restriction indicator.

 

The A-model PrecisionCut© Mowers, E-Cut© Hybrid Mowers, and TerrainCut© Mowers feature a radiator screen that is easily removed without tools and a tilt-out oil cooler for easy cleaning.


TechControl display TechControl display
Password-protected settings Password-protected settings
More control with the TechControl display with a large easy-to-read screen

Passcode-protected TechControl display enables quickly setting or changing mowing speed, turning speed, or transport speed to limit variations in performance by different operators.

Mow setting screen Mow setting screen

Quickly adjust the mow or transport speed to make sure mow speed is what is needed for the changing conditions. The setting can be adjusted precisely using a speedometer app on a smartphone or global positioning system (GPS) device.

Turn-speed setting screen Turn-speed setting screen

Use the TechControl to slow the machine during turns while mowing and protect against turf scuffing and aggressive turning operators.

 

The turn speed control engages when in mow and the cutting units are lifted for turns. Once the turn is made and the cutting units are lowered, the machine speed returns to the set mow speed.

 

The turn speed is a percentage of mow speed. When set to 100 percent, turn speed control is off or allows 100 percent of the mow speed in turns. Turn speed setting of 50 percent allows only 50 percent of the set mow speed to be reached during turns.

 

Here is an example:

Mow speed = 9.66 km/h (6 mph)
Turn speed set at 50 percent
Maximum turning speed will be 4.83 km/h (3 mph)

Input/output screen Input/output screen
Service timers screen Service timers screen

The A-model PrecisionCut© Mowers, E-Cut© Hybrid Mowers, and TerrainCut© Mowers have the latest in advanced diagnostics through the TechControl display. Most all diagnostics are performed while sitting in the operator's seat.

 

The TechControl has onboard visual diagnostics allowing quick and easy machine diagnostics, maximizing up time. The system allows technician to see inputs and outputs of the electrical system.  Also, the technician can see stored controller codes on the machine to aide in troubleshooting incidents that may have occurred while on the course.

 

The TechControl will also display the notification for maintenance of the hydraulic and engine oils using service timers to notify when it has reached the time to perform the required service.

Language settings Language settings
#

Choose from a list of several languages to use for the TechControl.

 

Operator warning notifications are incorporated into the TechControl and will alert the operator if a problem arises during operation.

 

 

Description

Hydraulic over temp

Hydraulic oil filter restriction

Engine oil pressure low

Engine coolant temperature

Reel motor

Battery voltage


Reel circuit power source 180-amp alternator Reel circuit power source 180-amp alternator
Electric motors drive cutting units Electric motors drive cutting units

The E-Cut© Hybrid Fairway Mowers are unique in that electrical power is used to minimize hydraulic leak opportunities in the reel circuit, but an engine is utilized to ensure optimal performance throughout the day. This presents an opportunity to further enhance machine performance through reduced sound levels and improved fuel savings, by running the machine at less-than-full throttle. When running the E-Cut Hybrid machines at the recommended reduced setting it does not sacrifice cut quality as the reel speed is still maintained at approximately 2200 rpm.

Mow engine speed screen Mow engine speed screen
Password-protected settings Password-protected settings

This reduced throttle setting is set quickly and easily using the TechControl display. Simply use the    password-protected mower set-up screen Engine Mow Speed to set maximum engine speed while in mow. Once set, the engine speed automatically uses this rpm when the machine is mowing. This allows complete control of sound levels and fuel savings.

 

The 7500A and 8000A E-Cut© Hybrid Fairway Mowers can be effectively run in mow at an engine rpm reduced to 2300 rpm. At this operating rpm, operators will experience noise reductions when compared to running the machines at full throttle.

 

In addition to the reduced sound levels, the operation at this engine rpm will reduce fuel usage due to slower engine rpm. Comparisons have shown that, depending on conditions and usage, fuel savings can be as high as 30 percent when running the machine at 2300 rpm as opposed to running at full throttle required by traditional hydraulic machines.


Large wheel motorsLarge wheel motors
eHydro™eHydro™

The eHydro© traction pump and wheel motors in the new A-model takes performance, traction, and operation to the next level.

 

We designed the new system to take on the most challenging course conditions. These improvements to the traction system makes the A-models ideal for undulating terrain providing superior performance and traction out on the course.

 

The traction system in the A-models is driven by a servo-controlled hydrostatic pump. The control of the pump is no longer mechanical linkages but instead it is electronic.

 

In total approximately 94 parts have been eliminated from the traction drive system along with 4 adjustments compared to prior models. The design reduced the complexity of the drive system meaning no more linkages to adjust or repair decreased routine maintenance and providing reliable day-in/day-out operation.

Forward/reverse pedalsForward/reverse pedals
#

The operator will like the eHydro, too. The pedal effort has been reduced, thus reducing the foot fatigue during many hours of mowing.


Rubber mounted front up stops Rubber mounted front up stops
Double rear up stop Double rear up stop

The 6500A, 6700A, 7500A, 7700A, and 8700A PrecisionCut© and 6500A and 7500A E-Cut© Hybrid Fairway Mowers all have cutting units that contact up stops for transport. These up stops are rubber and limit cutting units from swinging during transport. The lift system also folds the two wing units inside the tires to limit possibility of damage to the wing units when transporting through and around objects on the course.


Optional GRIP all-wheel drive Optional GRIP all-wheel drive
#

For superior traction with a true hydraulic four-wheel drive (4WD), the GRIP All-Wheel Drive Traction System is optional equipment for the PrecisionCut© and E-Cut© Hybrid fairway mowers. This system reduces wheel slip by sending flow from the front wheel to the opposite rear wheel.

For example, if the front right wheel starts to slip, hydraulic flow is diverted to the left rear wheel to maintain positive traction. By allowing the flow to cross over to the opposite rear wheel, the system maintains traction not only while climbing straight up hills, but also on side hills, as well. 

The GRIP All-Wheel Drive Traction System is always engaged when driving forward with the PrecisionCut and E-Cut Hybrid fairway mowers. There are no electronics to engage the 4WD system, simplifying the electrical system and the design of the valve at the rear of the machine.

In reverse, a standard switch is provided that disengages 4WD. The switch senses that the reverse pedal has been depressed and shuts off flow to the rear drive wheels. This ensures that the front drive tires are doing the work in reverse rather than the rear tires, minimizing wheel slip and scuffing of turf when backing up an incline.


Large wheel motors Large wheel motors
eHydro© eHydro©

The eHydro© traction pump and wheel motors in the new A-model takes performance, traction, and operation to the next level.

 

We designed the new system to take on the most challenging course conditions. These improvements to the traction system makes the A-models ideal for undulating terrain providing superior performance and traction out on the course.

 

The traction system in the A-models is driven by a servo-controlled hydrostatic pump. The control of the pump is no longer mechanical linkages but instead it is electronic.

 

In total approximately 94 parts have been eliminated from the traction drive system along with 4 adjustments compared to prior models. The design reduced the complexity of the drive system meaning no more linkages to adjust or repair decreased routine maintenance and providing reliable day-in/day-out operation.

Forward/reverse pedals Forward/reverse pedals
#

The operator will like the eHydro, too. The pedal effort has been reduced, thus reducing the foot fatigue during many hours of mowing.


Steering cylinder and linkage system Steering cylinder and linkage system

For superintendents who want stripes as straight as they are on the greens, the A-model PrecisionCut© Mowers and E-Cut© Hybrid Mowers do exactly that. Utilizing the same style steering cylinder as on the 2550 PrecisionCut and 2550 E-Cut Hybrid Riding Greens Mowers, the PrecisionCut and E-Cut Hybrid Mowers can mow the straightest lines of any mower in the industry today.

 

Traditional hydraulic cylinders have a rod on only one side of the cylinder. The cylinder on the A-models has one rod that goes through both sides of the cylinder. This equalizes volume and pressure on both sides of the cylinder packing, helping the operator make   perfectly straight lines with little effort.

 

This system also equalizes the steering effort, meaning easy turns whether turning to the right or to the left.


Grooved disc roller Grooved disc roller

The grooved disc roller can be used with 55.9-cm (22-in.) QA5 cutting units, in combination with the Greens Tender Conditioner and FTC, to provide additional roller options for fairway, tees, and approach areas.

The increased diameter improves the durability over smaller rollers, and it features hardened discs for improved wear which retains spring tension for reduced maintenance, making it an ideal roller for fairway, tee, and approach mowing.


Specs
Controls
Throttle Automatic controls with AutoPedal foot controls; manual control through TechControl display
Forward/reverse 2-pedal
Mower lift One-touch single handle
Parking brake Electric Switch on Command Arm for Internal Wet Disk Brakes
Seat Suspension seat with seat belts and arm rest; fore/aft adjustment; weight and lumbar adjustment
PTO Electric Switch on Command Arm
Tilt steering Left Foot operated for easy adjustment
Cutting Units
Number Five
Size Quick Adjust QA5: 55.9 cm
22 in.
Total width of cut 254 cm
100 in.
Height of cut Construction
2.0 to 28.5 mm
0.078 to 1.125 in.
Frequency of clip (FOC Reels) or Blade tip speed (decks) Rollers
Front and rear: 51 mm
2 in.
Optional: 76.2 mm
3 in.
11 Blade: 0.69 mm/km/h
0.044 in./mph
7 Blade: 1.09 mm/km/h
0.069 in./mph
Reel diameter 12.7 cm
5 in.
Dimensions
Height with ROPS 224 cm
88 in.
Length 323 cm
127 in.
Transport width 287 cm
113 in.
Mowing position width 295 cm
116 in.
Ground speed Mowing
0 to 12.8 km/h
0 to 8.0 mph
4WD mow speed
0 to 12.8 km/h
0 to 8.0 mph
Transport
0 to 18.5 km/h
0 to 11.5 mph
Reverse
0 to 6.4 km/h
0 to 5.0 mph
Engine
Type Direct Inject Turbocharged Diesel
Compliant emission regulation United States and Canada Tier 4
Horsepower Maximum rated horsepower
At 2800 rpm ISOC: 31 kW
At 2800 rpm ISOC: 41.6 hp
Cylinders Three
Displacement 1.568 L
95.69 cu in.
Air cleaner 2-stage dry element
Fuel Diesel
Cooling system Liquid centrifugal pump; forward machine location for optimum cooling
Operating weight
o o
Sound levels
Measuring standard ISO 11201
Attachments installed FTCs, reels engaged
Vehicle
Drive pump N/A due to Electric Driven Cutting units
Hydraulic system capacity 45.4 L
12 U.S. gal.
Fuel tank capacity 60.6 L
16 U.S. gal.
Steering Hydraulic power with double acting steering cylinder
Front drive tires 26.5x14-12 turf
Steering tires 20x12X10-8 turf
Ground pressure 69 kPa
10 psi
Brakes Internal hydraulic wet disc brakes with dynamic braking through closed loop hydrostatic system
ROPS Standard; meets ISO 21299 Standard
Warranty
w w
Accessories and Attachments
Bedknives

For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


BedknivesBedknives

Choice of four bedknives to meet the need for quality cuts to as low as 5/64 in. (2 mm).


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


Miscellaneous

Air-Ride Suspension Kit - BTC10392


Canopy - BTC10338


John Deere Golf Operator Videos and All Products Safety Video DVD Set - TCU23674


(1) 22 In. Fairway Tender Conditioners (FTC) Shaft and Blades - BM22671


(1) 22 In. Front Grass Catcher - BTC10909


(1) 22 In. Front Rotary Turf Brush - BM22761


(1) 22 In. Rear Grass Catcher - BTC11038


(1) 22 In. Rear Roller Power Brush  - BM22668


(1) 22 In. Smooth Roller Scraper  - BM22995


The rotary brush and GTC are powered by an external gear-drive attachment:

  • Gear-drive design allows the GTC to be turned off or on, a unique feature belt-drive designs cannot offer.
  • The gear-drive attachment adjusts the rotary brush or GTC to 1/32 in. (0.8 mm) below cut for more aggressive grooming or 7/32 in. (5.6 mm) above cut easily without tools.
  • The attachment can easily be raised or lowered into or out of the working position without any tools.

(1) QA5 Grass Catcher Lip Extension - BM23910


(1) Rear Roller Power Brush Drive - BM22527


2"x 22" Machine Grooved Roller Scraper - TCA19547


3"X22" GROOVE ROLLER SCRAPER - BM23002


4WD Conversion Kit - BTC10391


Front High Capacity Catcher with large paddle clip - BTC10217


Front High Capacity Catcher with large paddle clip - BTC10719


Grass Catcher Mounting Kit (set of 3) 1 needed per machine - BTC10605


Grass Catcher with large paddle clip (22 Low Profile) - BTC10216


Grass Catcher with large paddle clip (22 Low Profile) - BTC10718


Height of Cut Guage Bar - TCU13823


Hydraulic Down Pressure Kit - BTC10346


Left Hand Latch Catcher - BTC11011


QA5 Grass Catcher Side Plate Insert - BM24199


QA5 Slope Leveling Kit - BM24372


Rear Grass Catcher Bail Kit - BTC10501


Rear Grass Catcher with Handles - BTC10408


Right Hand Latch Catcher - BTC11010


Wing Latch Kit - BTC10194


Reel Cutting Unit Counter Weights

(1) Cutting Unit ONLY Counter Weight Kit - BM22762


(1) QA5 Cutting Unit Brush Only Counter Weight Kit - BM22705


(1) QA5 FTC/GTC ONLY Counter Weight Kit - BM22704


Rollers

(1) 22 In. 2 In. (5 cm) Diameter Hollow Smooth Roller - BM24202


Machine-grooved front rollerMachine-grooved front roller

Grooved front rollersGrooved front rollers

Grooved front rollers maintain height of cut while allowing superintendent to experience a better quality of cut versus a smooth roller.


(1) 22 In. 2 In. (5cm) MT Grooved  Roller - BTC10267


(1) 22 In. 3 In. (7.6 cm) Diameter Heavy Duty Grooved Disc Front Roller - BM25317


Spiral-grooved front rollerSpiral-grooved front roller

The 3-in. (7.6-cm) diameter spiral-grooved rollers with spiral endcaps should be used with seven-blade heavy-section cutting units for mowing tees, collars, approaches, or fairways.

 

The height-of-cut range with these rollers is 5/8 in. to 1-1/4 in. (16 mm to 32 mm). Using the 3-in. (7.6-cm) diameter spiral-grooved rollers with spiral endcaps for a height of cut greater than 3/4 in. (19 mm) requires changing the height-of-cut bolt on the rear adjusters to M10 x 70.

 

NOTE: These rollers should not be used for greens mowing.


(1) 2X22" MT SPIRAL Roller - BM23566


*Manufacturer's suggested price. MSRP may be different in California. Taxes, freight, setup, and delivery not included. Optional accessories and attachments not included. Equipment, models and prices may vary by dealer. Product options and accessories may not be available in all regions. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s website for additional information. Offers valid in the United States. Prices in U.S. dollars.
Belle Glade

2017 Northwest 16th Street
Belle Glade, FL 33430
561-996-6531

Map & Hours
Boynton Beach

1335 Neptune Dr
Boynton Beach, FL 33426
561-732-8905

Map & Hours
Brooksville

22255 Cortez Blvd
Brooksville, FL 34601
352-573-2720

Map & Hours
Fort Myers

9501 FL-82
Fort Myers, FL 33905
239-332-5045

Map & Hours
Fort Pierce

6150 Orange Ave
Fort Pierce, FL 34947
772-461-5568

Map & Hours
Immokalee

775 E Main St
Immokalee, FL 34142
239-657-4413

Map & Hours
Largo

6785 114th Ave
Largo, FL 33773
727-828-8200

Map & Hours
Leesburg

1800 US-441
Leesburg, FL 34748
352-315-1016

Map & Hours
Loxahatchee

13295 Southern Blvd
Loxahatchee, FL 33470
561-784-4000

Map & Hours
Naples

1945 Pine Ridge Rd
Naples, FL 34109
239-260-8800

Map & Hours
Odessa

2240 Success Dr
Odessa, FL 33556
727-842-8618

Map & Hours
Okeechobee

820 US-98
Okeechobee, FL 34972
561-296-7523

Map & Hours
Orlando

12049 S Orange Blossom Trail
Orlando, FL 32837
407-240-1023

Map & Hours
Palmetto

906 US-301
Palmetto, FL 34221
941-722-3281

Map & Hours
Plant City

2805 West, FL-60
Plant City, FL 33567
813-737-1660

Map & Hours
Sarasota

6209 McIntosh Rd
Sarasota, FL 34238
941-924-9709

Map & Hours
St Cloud

117 13th St
St Cloud, FL 34769
321-209-4888

Map & Hours
©2020 EFE, Inc. All Rights Reserved | Designed In-House by Everglades Equipment Group