John Deere 2500B PrecisionCut™ Diesel

Feature Overview
John Deere 2500B PrecisionCut™ Diesel
  • Greatly reduce triplex ring with exclusive offset cutting units
  • Save time with Quick Adjust Cutting Units
  • Exceptional contour-following and steering of cutting units in turns
  • On-board diagnostics
Number of cylinders 3-cylinder
Displacement 993 cc / 60.6 cu in.
Traction drive Hydrostatic, 2-pedal control
Cutting unit size, in. (cm) Quick Adjust QA5 floating: 55.9 cm / 22 in.
Feature Overview
John Deere 2500B PrecisionCut™ Diesel
  • Greatly reduce triplex ring with exclusive offset cutting units
  • Save time with Quick Adjust Cutting Units
  • Exceptional contour-following and steering of cutting units in turns
  • On-board diagnostics
Number of cylinders 3-cylinder
Displacement 993 cc / 60.6 cu in.
Traction drive Hydrostatic, 2-pedal control
Cutting unit size, in. (cm) Quick Adjust QA5 floating: 55.9 cm / 22 in.
We are here to help
Features

Easy service access to minimize time to perform daily maintenance tasks

Daily service checks Daily service checks
Access panel Access panel

Several serviceability features were incorporated into the design of the 2500B PrecisionCut© Riding Greens Mower to make routine checks and adjustments as easy as possible.

Features include:

  • Good visibility to components, with a tilt-back hood and tilt-up seat platform. With the hood and seat platform in the raised position, access and visibility to the components underneath is very good.
  • All daily service checks — engine oil level, air restriction indicator, engine coolant level, and hydraulic oil level — are made from the left side of the machine.
  • Quick-attatch cutting units — one pin located at the front of the lift arms removes the cutting units from the traction unit with no tools.
  • Quick-attatch cutting unit motors — just loosen the two hold-down nuts, twist the motor, and pull it out away from the cutting unit.
  • Remote grease fittings for the front lift arms are located on the front hydraulic fitting bulkhead. These remotely mounted fittings allow ease of lubrication for the front lift arm pivot pins.
  • Electronic controller that provides service diagnostics by means of lighted circuits.
  • There is also an access panel on the operator platform that can be easily removed to provide access to the backlap valve and battery.

Found behind operator Found behind operator
Larger capacity Larger capacity
Access from both sides Access from both sides

Operator storage area is located behind the operator for easy access from either side of the machine.  This large storage area is design to hold items such as jackets or other items that may be needed by the operator. 


Fuel gauge and filler cap Fuel gauge and filler cap
Twin-sheet design fuel tank Twin-sheet design fuel tank

The fuel tank is a twin-sheet design to and meets fuel tank regulatory requirements and still has the capacity to get through a normal day without refueling. Easy access to the fuel cap and clear view of the fuel gauge keeps the operator productive all day.


Most golf courses want to mow the greens and collect the grass for a premium cut and even and smooth appearance. The most challenging concern with catching grass with a greens mower is that as the grass catcher fills with material, its weight is transferred to the cutting unit. This problem is multiplied with a riding greens mower because there are three cutting units and grass catchers collecting different amounts of grass, meaning different weights are applied to the three cutting units.

 

If the weight cannot be removed from the grass catchers, the different weights can cause different heights of cut with each cutting unit, leaving poor playing conditions and after-cut appearance. This is especially noticeable through undulations of a green and on the clean-up pass. The grass catchers on the riding greens mowers have been designed for optimum catching efficiency while maintaining a consistent, effective height of cut.

Grass catcher clip (1) and lift arm bracket (2) Grass catcher clip (1) and lift arm bracket (2)

The exclusive John Deere grass catcher transfers approximately two-thirds of the weight to the vehicle's lift arm. This helps maintain a more-consistent cutting height to ensure a uniform cut across all three cutting units.

 

The front grass catchers can be removed and installed with one hand because of an innovative clip system. The clip secures the catcher to an adjustable bracket on the lift arm, transferring weight from the catcher to the lift arm as clippings accumulate in the catcher.

Rear grass catcher (1) and bail system (2) Rear grass catcher (1) and bail system (2)

The rear grass-catcher mounting system simplifies removal and installation of the rear grass catcher and reduces effort.

 

The retaining-bail system for the rear grass catcher also uses the exclusive John Deere design to transfer the weight of the grass catcher to the lift arm.

Rear grass catcher Rear grass catcher

The grass catcher can be easily removed, without spilling the clippings, by rotating the grass catcher back toward the front of the machine until the front grass catcher lip is above the cutting unit side plate. Then, simply pull it out to the side. This can be accomplished with the cutting unit in the raised or lowered position.

Grass catcher channel Grass catcher channel

A channel in the cutting unit side frames guides the grass catcher onto the cutting unit. The channel in the castings ensures the grass-catcher lip maintains its relationship with the cutting unit when following undulations, providing for better grass-catching efficiency.

Adjustable top shield Adjustable top shield

Adjustable cutting-unit top shields also ensure that grass is thrown into the back of the catcher, even as the reel diameter decreases due to wear. The catchers are shaped and vented to allow the air from the reel to escape while retaining the clippings.

Top-shield extension for dry conditions Top-shield extension for dry conditions

Extensions for the cutting-unit top shields are for use in dry conditions to maximize the flow of dry clippings into the grass catcher. If mowing predominantly in wet-turf conditions, remove the cutting unit shield extensions to reduce buildup and accumulation of clippings on the front of the grass catcher.


Offset cutting units Offset cutting units

The innovative offset design staggers wheel tracks in the cleanup cut by simply changing direction of travel each day. This allows the turf an additional day to recover before being driven over again, and serves to minimize triplex ring and compaction.

The cutting units offset to the left-hand side of the machine. This provides good visibility to the center cutting unit. The traction unit frame is designed to maximize visibility down the left-hand side of the machine from the operator's point of view.


The optional direct mount front grass catchers provide the choice of systems to meet the needs on your golf course.

#

The grass catcher is mounted directly to the front cutting unit using a similar design as the SL Walk Greens Mowers.

This provides quick access for the removal and installation of the grass catcher as well as superior ground following and collection due to position of the catcher to the cutting unit.

It is recommended that catchers be emptied after each green during normal and heavy growth times to reduce weight on the cutting unit.

The direct mount grass catchers will fit model year 2009 to current 2500B and 2500E E-Cut Riding Greens Mowers with Quick-Adjust 5 (QA5) cutting units.

Rear grass catcher (1) and bail system (2) Rear grass catcher (1) and bail system (2)

The rear grass-catcher mounting system simplifies removal and installation of the rear grass catcher and reduces effort.

Rear grass catcher Rear grass catcher

The grass catcher can be easily removed without spilling the clippings by rotating the grass catcher back toward the front of the machine until the front grass catcher lip is above the cutting unit side plate. Then, simply pull it out to the side. This can be accomplished with the cutting unit in the raised or lowered position.

Adjustable top shield Adjustable top shield

Adjustable cutting-unit top shields also ensure that grass is thrown into the back of the catcher, even as the reel diameter decreases due to wear. The catchers are shaped and vented to allow the air from the reel to escape while retaining the clippings.

Top-shield extension for dry conditions Top-shield extension for dry conditions

Extensions for the cutting-unit top shields are for use in dry conditions to maximize the flow of dry clippings into the grass catcher. If mowing predominantly in wet-turf conditions, remove the cutting unit shield extensions to reduce buildup and accumulation of clippings on the front of the grass catcher.


14-blade reel 14-blade reel
#

Using the 14-blade reel on greens mowers will lower the frequency of clip and also provide a clean, smooth cut. It can increase the playability of the putting surface and greens speed.

 

Frequency of clip (FOC) is defined as the distance traveled between consecutive cuts. In other words, it is how far the machine moves from the time one blade passes across the bedknife until the next blade passes. The lower the frequency of clip, the less distance that is traveled until the next blade passes.

 

There is a point of diminishing returns when it comes to frequency of clip. The less distance the mower travels between consecutive cuts, the more times the same grass blade is going to be impacted by the reel. Too low a frequency of clip can cause bruising of the turf - especially in the overlap from pass to pass.

 

Frequency of clip is often used as a measurement of cut quality, however there are other key factors that attribute to gaining good quality of cut. The factors that lead to good cut quality are:

  • Geometry of the cutting unit
  • Sharpness of reels and bedknife
  • Proper cutting-unit setup (parallel and bedknife-to-reel clearance)
  • Height of cut (HOC) (effective versus bench HOC)
  • Bedknife selection
  • Roller selection for the turf conditions
  • Turf conditions

The geometry of John Deere cutting units makes the optimum range for frequency of clip between 0.160 in. (4.064 mm) and 0.190 in. (4.824 mm) for walk greens mowers. This is where the technology of the PrecisionCut© walk greens mowers excels and provides a superior cut and after-cut appearance.

 

Machines

14-blade reel part number

Minimum FOC
in. (mm)

Minimum FOC with AMT2865*
in. (mm)

180SL PrecisionCut Walk Greens Mower

TCA23624

0.141 (3.58)

0.123 (3.12)

220SL PrecisionCut Walk Greens Mower

TCA23623

0.141 (3.58)

0.123 (3.12)

*Frequency speed-up kit


Grooved disc rollerGrooved disc roller

The grooved disc roller can be used with 55.9-cm (22-in.) Quick-Adjust 5 (QA5) cutting units, in combination with the GTC and FTC, to provide additional roller options for fairway, tees, and approach areas.

 

The increased diameter improves the durability over smaller rollers and it features hardened discs for improved wear which retains spring tension for reduced maintenance, making it an ideal roller for fairway, tee, and approach mowing.


Lift-arm design Lift-arm design

The cutting-unit suspension and lift arms are designed with down stops for the lift arms to rest on when the cutting units are lowered to mow. This transfers the weight of the lift arms onto the traction unit frame rather than adding weight to the cutting unit.

Ball-joint mounting design Ball-joint mounting design

The cutting-unit mounting system has a ball-joint swivel designed to allow the cutting unit to float independently of the lift arm. This design minimizes scalping and promotes a consistent height of cut by allowing the cutting unit to easily follow ground contours and steer in turns.

 

The cutting units can be easily and quickly removed from the lift arms by pulling the quick pin located behind the ball swivel joint and disconnecting the cutting unit support chain from the lift arm. This disengages the cutting unit assembly from the lift arm for service.

 

The cutting-unit drive motor also has a Quik-Tatch system that allows the technician to quickly remove the motor from the cutting unit for service. Simply loosen the mounting bolt that secure the motor to the bearing housing and twist the motor a quarter turn to remove.


Diesel engine Diesel engine

The 2500B PrecisionCut© and 2500E E-Cut© Hybrid Riding Greens Mowers use a 19.6 hp* (14.6 kW) gross (per SAE J1995 at 3000 rpm) liquid-cooled diesel engine for smooth, efficient, and quiet operation.

 

With the 3-cylinder diesel engine and a large 7.9-U.S. gal. (29.9-L) fuel tank, the 2500B and 2500E give the operator power and fuel for a productive day of mowing.

 

*Engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s website for additional information.


ROPS with seat belt ROPS with seat belt

A ROPS and retractable seat belt are standard equipment on both the 2500B PrecisionCut© and 2500E E-Cut© Hybrid Riding Greens Mowers. The ROPS meets ISO21299 standards.


Smooth and turf tire options shown Smooth and turf tire options shown
Balloon-rounded tire option Balloon-rounded tire option

There are four tire options:

  • 18x10.50-10 2-ply smooth tires are recommended for those who want the minimum amount of ground compaction. These tires have a large footprint to spread the weight of the vehicle over a larger area. This tire also lowers the overall height of the machine and reduces ground clearance of the cutting units. Compensation for ground clearance can be made by adjusting the cutting unit chain on the back of the cutting unit.
  • 20x10-10 4-ply rated balloon-rounded smooth tires are recommended for those who want maximum ground clearance, increased ply rating and desire to use a more rounded tire. The 4-ply side wall rating has recommended operating tire pressure of 103 kPa (1.03 bar) (15 psi). Increased pressure may leave marks in softer turf conditions.
  • 20x10-10 2-ply smooth tires are recommended for those who want maximum ground clearance while operating at the lower tire pressure of 83 kPa (0.83 bar) (12 psi).
  • 20x10-10 4-ply rated smooth tires are recommended for those who want maximum ground clearance and increased ply rating. The 4-ply sidewall rating has recommended operating tire pressure of 103 kPa (1.03 bar) (15 psi). Increased pressure may mark in softer turf conditions.
  • 20x10-10 turf tires are for those who need additional traction for mowing more difficult areas, such as elevated tees or fairways.

 

Each of these tire options includes a complete set of three tires and wheels that are all the same size. (This includes the turf tires, which come as a set of three treaded tires.)


Rear attaching yokeRear attaching yoke
#

Low weight and compaction of a riding greens mower with the mowing system of a fairway mower equals great quality of cut in fairways and surrounds.

 

Many golf courses want to mow their fairways and other areas with riding greens mowers as a way to decrease compaction of the turf. However, the front-attaching-point yoke system used for greens is not the ideal solution for other areas due to the mowing speed, and the terrain is not as smooth as a green.

The 22-in. (55.88-cm) cutting unit rear-attaching-point yoke kit attaches to the rear cutting unit to help keep the rear roller on the ground consistently in undulating terrain. This also substantially improves cut quality by maintaining a consistent height of cut in virtually any condition. Rather than pushing the cutting unit through the turf, the yoke system pulls the cutting unit through the turf keeping the back end of the cutting unit engaged with the turf.


Grooved disc roller Grooved disc roller

The grooved disc roller can be used with 55.9-cm (22-in.) QA5 cutting units, in combination with the GTC and FTC, to provide additional roller options for fairway, tees, and approach areas.

 

The increased diameter improves the durability over smaller rollers, and it features hardened discs for improved wear which retains spring tension for reduced maintenance, making it an ideal roller for fairway, tee, and approach mowing.


Rear attaching yoke Rear attaching yoke

Low weight and compaction of a riding greens mower with the mowing system of a fairway mower equals great quality of cut in fairways and surrounds.

 

Many golf courses want to mow their fairways and other areas with riding greens mowers as a way to decrease compaction of the turf. However, the front-attaching-point yoke system used for greens is not the ideal solution for other areas due to the mowing speed, and the terrain is not as smooth as a green.

The 55.9-cm (22-in.) cutting unit rear-attaching-point yoke kit attaches to the rear cutting unit to help keep the rear roller on the ground consistently in undulating terrain. This also substantially improves cut quality by maintaining a consistent height of cut in virtually any condition. Rather than pushing the cutting unit through the turf, the yoke system pulls the cutting unit through the turf keeping the back end of the cutting unit engaged with the turf.


Specs
Key Specs
Number of cylinders 3-cylinder
Displacement 993 cc
60.6 cu in.
Traction drive Hydrostatic, 2-pedal control
Cutting unit size, in. (cm) Quick Adjust QA5 floating: 55.9 cm
22 in.
Certification
Number ANSI B71.4-2004
ROPS 2-Post SAE J21294 Roll Over Protection Structure with seat belts meets ISO 21299 standards
Engine EPA Tier 2, Interim Tier 4
Cutting Units
Size, in. (cm) Quick Adjust QA5 floating: 55.9 cm
22 in.
Backlapping Standard on-board micro-backlapping and reel speed control
Clip frequency For 14 blade: 0.541 mm/km/h
0.034 in./mph
With 11-blade reel: 0.689
0.044 in./mph
With 7-blade reel: 1.082 mm/km/h
0.069 in./mph
Front rollers Optional smooth, grooved, or spiral: 5.1 cm
2 in.
Reel diameter 12.7 cm
5 in.
Bedknife adjustment Bedknife-to-reel
Height of cut 2.0-19.0 mm
0.078-0.75 in.
with front roller: 51 mm
2 in.
or 16-32 mm
0.625-1.25 in.
with frotner roller: 76 mm
3 in.
Number of blades 7 or 11 blades
Mower lift (1) cylinder for front two units; (1) cylinder for rear unit
Reel speed Adjustable
Electrical System
Charging system Flywheel, alternator
Alternator capacity 20 amp
Battery type BCI group 40 maintenance-free: 12 V
Starter Electric (solenoid shift)
Engine
Type
Diesel model
IDI Diesel
Horsepower
Diesel horsepower
Per SAE J1995: 14.6 kW
19.6 hp
*Engine hp is provided by the engine manufacturer to be used for comparison purposes only. Actual operating hp will be less. Refer to the engine manufacturer’s web site for additional information.
Air cleaner Semi-cyclone, dry-type, dual stage
Cooling Oil filter
Full-flow filter
Engine oil capacity
With filter: 2.2 L
2.3 U.S. qt
Pressurized lubrication system
Standard
Number of cylinders
3-cylinder
Displacement
993 cc
60.6 cu in.
Liquid
Instrumentation
Engine oil pressure LED Warning Light
Alternator LED Warning Light
Hydraulic oil temperature LED Warning Light
Engine coolant temperature LED Warning Light
Hourmeter Digital
Operator Controls
Steering Hydrostatic, adjustable steering column
Reel drive and reel lift Right-hand operated (optional foot-lift controls)
Throttle Right hand
Park brake Right foot
Hydrostatic speed control Forward
Right foot
Reverse
Right foot
Ignition Key start and shutoff
Glow plug switch and indicator light Automatic, on instrument panel
Sound Levels
Operator ear 82 dBA
Measuring standard ISO 11201
Attachments installed GTCs and Power Brushes, reels engaged
Vehicle Specifications
Brakes Type
Dual, 15.2 cm
6 in.
Single-pedal, 2-wheel disc brakes
Mowing speed Adjustable mow stop: 0-7.1 km/h
0-4.4 mph
Transport speed 0-12.9 km/h
0-8.0 mph
Reverse speed 0-4.8 km/h
0-3 mph
Ground clearance with catcher 10.2 cm
4 in.
Fuel tank capacity In a single tank: 29.5 L
7.8 U.S. gal.
Muffler Horizontal discharge below frame
Hydrostatic drive system capacity 28.8 L
7.6 U.S. gal.
Hydraulic reservoir capacity (only) 20.4 L
5.4 U.S. gal.
Ground drive, reel drive Drive wheels
Front
Traction drive
Hydrostatic, 2-pedal control
Reel drive
Hydraulic
Pump 3-section gear
Reel control valves Electro-hydraulic, one valve reel on-off and one valve raise-lower
Filtration 10-micron
Wheels and tires Front/rear
18x10.5-10, 2-ply, smooth (low compaction)
20x10-10, 2-ply or 4-ply, smooth
or 20x10-10, 2-ply, turf
Weights and Dimensions
Wheelbase 129.5 cm
51 in.
Tread width 101.5 cm
40 in.
Mowing position width 157.5 cm
62 in.
Turning radius, uncut circle 45.7 cm
18 in.
Weight (full fluids, no operator or fuel) 637.3 kg
1405 lb
Height With ROPS: 194.6 cm
76.5 in.
Accessories and Attachments
Bedknives

For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


BedknivesBedknives

Choice of four bedknives to meet the need for quality cuts to as low as 5/64 in. (2 mm).


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


For the 3225C and the 3235C equipped with seven-blade standard cutting units, ET17533 will be shipped as the standard 22-in. bedknife.

 

For the 3225C and 3235C equipped with ESP™ cutting units, ET17751 (minimum height of cut is 12 mm) will be shipped as the standard bedknife for the five-blade and eight-blade cutting units. The 10-blade cutting unit will be shipped with MT1928 (minimum height of cut is 9.5 mm) low-cut fairway bedknife.

 

Following are all the bedknife options available for lightweight fairway mower cutting units:


Cutting Units

(1) QA5 22 In. Vertical Cutting Unit With Front Roller Less Motor - BM25129


(1) QA5 Eleven Blade 22 In. Cutting Unit w/Adjustable 2.0 mm Bedknife, Less Front and Rear Roller & Motor - BM25128


(1) QA5 Seven Blade 22 In. Heavy Section Blade Cutting Unit With Adjustable 4.8 mm Bedknife, Less Yokes, Front and Rear Roller & Motor - BM25127


(1) Quick Adjust 5 (QA5) Fourteen Blade 22 In. (55.9 cm) Cutting Units with Adjustable 2.0mm Bedknife - BM25338


Miscellaneous

Weight Transfer Grass Catcher Mounting Kit - BTC10914


(1) 22 In. Fairway Tender Conditioners (FTC) Shaft and Blades - BM22671


(1) 22 In. Front Rotary Turf Brush - BM22761


(1) 22 In. Greens Tender Conditioner (GTC) Shaft and Blades - BM22471


(1) 22 In. Rear Roller Power Brush  - BM22668


(1) 22 In. Smooth Roller Scraper  - BM22995


The rotary brush and GTC are powered by an external gear-drive attachment:

  • Gear-drive design allows the GTC to be turned off or on, a unique feature belt-drive designs cannot offer.
  • The gear-drive attachment adjusts the rotary brush or GTC to 1/32 in. (0.8 mm) below cut for more aggressive grooming or 7/32 in. (5.6 mm) above cut easily without tools.
  • The attachment can easily be raised or lowered into or out of the working position without any tools.

(1) QA5 22 In. Front Rotary DT Brush - BM24730


(1) QA5 Grass Catcher Lip Extension - BM23910


(1) Rear Roller Power Brush Drive - BM22527


Rear attaching yokeRear attaching yoke
#

Low weight and compaction of a riding greens mower with the mowing system of a fairway mower equals great quality of cut in fairways and surrounds.

 

Many golf courses want to mow their fairways and other areas with riding greens mowers as a way to decrease compaction of the turf. However, the front-attaching-point yoke system used for greens is not the ideal solution for other areas due to the mowing speed, and the terrain is not as smooth as a green.

The 22-in. (55.88-cm) cutting unit rear-attaching-point yoke kit attaches to the rear cutting unit to help keep the rear roller on the ground consistently in undulating terrain. This also substantially improves cut quality by maintaining a consistent height of cut in virtually any condition. Rather than pushing the cutting unit through the turf, the yoke system pulls the cutting unit through the turf keeping the back end of the cutting unit engaged with the turf.


2"x 22" Machine Grooved Roller Scraper - TCA19547


3"X22" GROOVE ROLLER SCRAPER - BM23002


Arm Rest Kit (Includes One Arm Rest and Hardware) - AMT2477


Cutting Unit Top Shield Extension (Set of 3) - BM23080


Cutting Unit Yokes Kit (22") for MY1998-2008 - TCB11356


Cutting Unit Yokes Kit for MY 2009 – Current or QA5 Cutting Units - TCB11341


Dew whip kitDew whip kit

Contains dew whip holder and hardware, for installation on side of hood.


Dew Whip with end support bracket - BTC10686


Direct Mount Cutting Unit Yoke Kit for MY 2009 – Current or QA5 Cutting Units - BTC10655


Direct Mount Front Grass Catcher - BTC10726


Direct Mount QA5 Grass Catcher Brackets - BM24900


Grass Catcher Mounting Kit - TCB11721


Grass Catcher with large paddle clip (22 Low Profile) - BTC10718


Greens mower convenience kitGreens mower convenience kit

Includes storage area pad and elastic storage retainer.


Height of Cut Gauge Bar - AMT2978


Hydraulic oil leak detection kitHydraulic oil leak detection kit

Kit includes parts needed to install a hydraulic oil leak detector for those desiring additional insurance against potential turf damage.

 

This kit will fit either gas or diesel 2500B Tri-Plex Greens Mowers and will alert the operator with both an audible alarm and a visual warning light in the event a hydraulic oil leak is detected.


Light kitLight kit

Includes one halogen beam working light for early-morning or late-evening operation.


QA5 Grass Catcher Side Plate Insert - BM24199


Rear Grass Catcher Bail Kit - BTC10407


Rear Grass Catcher with Handles - BTC10408


For increased traction in adverse, wet, or sloped mowing areas.

 

Third-wheel assist is automatically engaged when the PTO switch is pulled to the on position to engage the mow circuit. This also automatically reduces forward speed to 4 mph (6.4 km/h).


Tires and Wheels (18x10.50-10), (3) Smooth Floatation - BM19750


Tires and Wheels (20x10.00-10), (3) Ballon Rounded Edge Smooth 4 Ply-Rated - BTC10841


Tires and Wheels (20x10.00-10), (3) Smooth - BM19748


Tires and Wheels (20x10.00-10), (3) Smooth 4 Ply-Rated - BTC10071


Tires and Wheels (20x10.00-10), (3) Turf Guard Traction - BM19749


Reel Cutting Unit Counter Weights

(1) Cutting Unit ONLY Counter Weight Kit - BM22762


(1) QA5 Cutting Unit Brush Only Counter Weight Kit - BM22705


(1) QA5 FTC/GTC ONLY Counter Weight Kit - BM22704


Rollers
Machine-grooved front roller with solid endcapsMachine-grooved front roller with solid endcaps

Machine-grooved front rollerMachine-grooved front roller

Grooved front rollersGrooved front rollers

Grooved front rollers maintain height of cut while allowing superintendent to experience a better quality of cut versus a smooth roller.


Wide tube/hollow smooth front rollerWide tube/hollow smooth front roller

(1) 22 In. 2 In. (5cm) MT Grooved  Roller - BTC10267


(1) 22 In. 3 In. (7.6 cm) Diameter Heavy Duty Grooved Disc Front Roller - BM25317


Spiral-grooved front rollerSpiral-grooved front roller

The 3-in. (7.6-cm) diameter spiral-grooved rollers with spiral endcaps should be used with seven-blade heavy-section cutting units for mowing tees, collars, approaches, or fairways.

 

The height-of-cut range with these rollers is 5/8 in. to 1-1/4 in. (16 mm to 32 mm). Using the 3-in. (7.6-cm) diameter spiral-grooved rollers with spiral endcaps for a height of cut greater than 3/4 in. (19 mm) requires changing the height-of-cut bolt on the rear adjusters to M10 x 70.

 

NOTE: These rollers should not be used for greens mowing.


(1) 2X22" MT SPIRAL Roller - BM23566


*Manufacturer's suggested price. MSRP may be different in California. Taxes, freight, setup, and delivery not included. Optional accessories and attachments not included. Equipment, models and prices may vary by dealer. Product options and accessories may not be available in all regions. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s website for additional information. Offers valid in the United States. Prices in U.S. dollars.
Belle Glade

2017 Northwest 16th Street
Belle Glade, FL 33430
561-996-6531

Map & Hours
Boynton Beach

1335 Neptune Dr
Boynton Beach, FL 33426
561-732-8905

Map & Hours
Brooksville

22255 Cortez Blvd
Brooksville, FL 34601
352-573-2720

Map & Hours
Fort Myers

9501 FL-82
Fort Myers, FL 33905
239-332-5045

Map & Hours
Fort Pierce

6150 Orange Ave
Fort Pierce, FL 34947
772-461-5568

Map & Hours
Immokalee

775 E Main St
Immokalee, FL 34142
239-657-4413

Map & Hours
Largo

6785 114th Ave
Largo, FL 33773
727-828-8200

Map & Hours
Leesburg

1800 US-441
Leesburg, FL 34748
352-315-1016

Map & Hours
Loxahatchee

13295 Southern Blvd
Loxahatchee, FL 33470
561-784-4000

Map & Hours
Naples

1945 Pine Ridge Rd
Naples, FL 34109
239-260-8800

Map & Hours
North Port

2825 Commerce Parkway
North Port, FL 34289
941-924-9709

Map & Hours
Odessa

2240 Success Dr
Odessa, FL 33556
727-842-8618

Map & Hours
Okeechobee

820 US-98
Okeechobee, FL 34972
863-763-1921

Map & Hours
Orlando

12049 S Orange Blossom Trail
Orlando, FL 32837
407-240-1023

Map & Hours
Palmetto

906 US-301
Palmetto, FL 34221
941-722-3281

Map & Hours
Plant City

2805 West, FL-60
Plant City, FL 33567
813-737-1660

Map & Hours
St Cloud

117 13th St
St Cloud, FL 34769
321-209-4888

Map & Hours
©2020 EFE, Inc. All Rights Reserved | Designed In-House by Everglades Equipment Group