Without the use of AIG, drawn implements are susceptible to implement drift caused by varying soil conditions as well as gravity in sidehill applications. John Deere AIG automatically steers the implement to the guidance line by providing GPS receiver position data to the implement steering system, reducing the adverse impact of implement drift
The benefits of John Deere AIG include:
Shared Signal can also be used with AIG to improve performance and reduce the overall cost of the system.
The tractor and implement can use a combination of StarFire receivers. Use the following chart to determine the correct receiver configuration.
Tractor | Implement | Recommended |
StarFire 3000 | StarFire 3000 | Yesâ |
StarFire iTC | StarFire iTC | Yes |
StarFire 3000 | StarFire iTC | Yes* |
StarFire iTC | StarFire 3000 | Yes* |
â John Deere Shared Signal is only available when using two StarFire 3000 Receivers
*For optimal AIG performance, the StarFire 3000 Receiver should be mounted on the implement.
AIG helps optimize the use of inputs by increasing accuracy at the implement and facilitating seamless, repeatable passes throughout the growing season.
AIG can help to reduce input costs in a variety of applications. Potato producers and other specialty crop producers that make frequent passes through the field have seen the value of AIG as they precisely plant and care for their crops. Additionally, producers employing strip-till practices are better able to align their seed placement with their fertilizer placement, maximizing the uptake of their valuable nutrients.
Maintaining the best crop quality is important in all farming operations, and is made especially difficult in cropping practices that require multiple passes through the field. Each pass during the production cycle puts the crop at risk. With AIG, producers no longer have to worry about the emerged crop, as both the tractor and implement are operating on the A-B line.
A risk is also minimized when seed is planted with AIG. The improved precision of seed placement provides a straighter path for subsequent passes throughout the season. Compaction and crop disturbance are also reduced as AIG achieves its precision by keeping the implement and tractor on the same guidance path.
At the end of the season, the results are better crop quality and improved yield, a value all producers can appreciate.
Active Implement Guidance (AIG) requires an implement steering mechanism. This is common with any active implement supplier on the market. The method of controlling the mechanism can only be found from John Deere.
John Deere controls the implement steering device through the tractor's SCV. This industry-exclusive technology allows operators to engage and disengage AIG quickly and easily.
Operators appreciate this when turning in fields with limited headland space. Simply disengage AIG and manually straighten out the implement after a turn by feathering the SCV lever.
Many minutes are saved, even with the most experienced operators, by eliminating the process of backing up after turns to align implements. The time an operator spent getting frustrated turning large implements can now be spent enjoying planting.
The fingertip controls also provide ease when parking implements in tight places or pulling through narrow spaces.
Fingertip control is available for
Other tractors are compatible with John Deere AIG with the use of an external SCV.
AIG is available for all other John Deere and non-John Deere tractors with the addition of an external SCV valve and SCV switch. Both can be ordered from a John Deere dealer. The tractor can have an open or a closed-center hydraulic system.
AutoTrac© assisted steering system paired with Active Implement Guidance (AIG) allows operators to be more productive as they focus on tasks other than steering while traveling down the field.
When operators have to spend their entire workday manually steering a machine while watching for obstacles and checking to make sure the implement is operating as expected, they tend to get worn out.
Using AutoTrac and AIG together greatly reduces the strain on the operator because the system accurately guides the implement down the most optimum pass, accurately placing inputs, such as seed or fertilizer, in the field.
Other benefits to the operator:
All of these benefits result in more uptime for the equipment and an operator who is more alert throughout the day, a benefit everyone can appreciate.
First introduced with the StarFire© 3000 Receiver, the StarFire 6000 and StarFire 6000 Integrated continue to provide shared signal functionality when pairing two receivers with AutoTrac© Implement Guidance, Active Implement Guidance©, or Machine Sync combine harvest automation via the GreenStar© 3 2630 Display, Generation 4 4600 CommandCenter©, or 4640 Universal Display. Shared signal allows correction signals to be communicated between a pair of receivers, improving relative system accuracy and reducing the initial investment required to use AutoTrac Implement Guidance, Active Implement Guidance, or Machine Sync combine harvest automation.
Supported configurations:
Leader definition - tractor receiver for Active Implement Guidance, combine receiver for Machine Sync combine harvest automation
Follower definition - implement receiver for Active Implement Guidance, grain cart tractor receiver for Machine Sync combine harvest automation
NOTE: StarFire 6000 must be updated to 19-1 (4.10J) software update to ensure performance and compatibility with shared signal.
NOTE: StarFire 6000 leader to StarFire 3000 follower is not a supported configuration.
NOTE: StarFire 3000 cannot be used in combination with the StarFire 6000 Integrated.
Shared signal enables StarFire receivers to share information when paired using implement guidance. This allows a StarFire receiver using a lower accuracy to be used on the implement for an implement guidance system and take advantage of the higher accuracy used by the machine receiver. The following table describes the accuracy expected from this system:
Machine receiver activation level |
Implement receiver activation level |
Overall system accuracy level |
Relationship between two receivers |
SF3/SF2 |
SF1 |
SF3/SF2 |
RTK |
RTK |
SF1 |
RTK |
RTK |
RTK |
SF3/SF2 |
RTK |
RTK |
Shared signal enables StarFire receivers to share information when paired using Machine Sync combine harvest automation. This allows the two vehicle receivers to maximize system performance during harvest. To ensure optimal performance and compatibility, always update receivers to the most current software version available on StellarSupport© portal. The following table describes the accuracy expected from this system:
Combine receiver activation level |
Grain cart tractor receiver activation level |
Overall system accuracy level |
Relationship between two receivers |
SF1 |
SF1 |
SF1 |
RTK |
SF3/SF2 |
SF1 |
SF3/SF2 |
RTK |
SF3/SF2 |
SF3/SF2 |
SF3/SF2 |
RTK |
RTK |
SF1 |
RTK |
RTK |
RTK |
SF3/SF2 |
RTK |
RTK |
This document lists all the compatible equipment approved with the software update 20-1 release and is subject to change with newer software updates. To ensure complete and proper compatibility, the most current version of implement control unit software, Generation 4 Display software, or compatible farm management information software (FMIS) should be used. Non-current software versions will require an update before support can be provided. Unapproved software version configurations will not be supported.
The software update 20-1 release is only compatible with 4600 CommandCenter© v2 processors. Software update 17-2 is the last release that was compatible with 4600 v1 processors.
Server serial numbers are as follows:
John Deere Large Ag Tractors
John Deere Large Ag Tractors (list of all automatically detected machines) |
Model year | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | ||
9R/9RT/9RX Series | 2018 and newer | X | --- | X | X |
9R/9RT/9RX Series | 2015-2017 | * | --- | X | X |
9R/9RT Series | 2012-2014 | --- | --- | X | X |
9030/9030T Series | 2008 and newer | --- | --- | X | X |
9020/9020T Series | 2002-2007 | --- | --- | X | --- |
9000 Series | 1997-2001 | --- | --- | X | --- |
9000T Series | 2000-2001 | --- | --- | X | --- |
8R/8RT Series | 2018 and newer | X | --- | X | X |
8R/8RT Series | Mid-2014 - 2017 | * | --- | X | X |
8R/8RT Series | 2010-2013 | --- | --- | X | X |
8030/8030T Series | 2006 and newer | --- | --- | X | X |
8020/8020T Series | 2002-2005 | --- | --- | X | --- |
8010/8010T Series | 2000-2002 | --- | --- | X | --- |
8000 Series | 1994 | --- | --- | X | --- |
8000T Series | 1997-1999 | --- | --- | X | --- |
7R Series | 2018 and newer | X | X | X | X |
7R Series | 2014-2017 | * | --- | X | X |
7R Series | 2011-2013 | --- | --- | X | X |
7J Series | 2018 and newer | --- | --- | X | X |
7030 Series | 2007 and newer | --- | --- | X | X |
7030 Series (Large Frame) | 2007 and newer | --- | --- | X | X |
7030 Series (Small Frame) | 2006 and newer | --- | --- | X | X |
6030 Series (Small Frame) | 2006 and newer | --- | --- | X | X |
6R Series | 2018 and newer | X | X | X | X |
6R Series (Final Tier 4) | 2015-2017 | * | --- | X | X |
6R Series (Interim Tier 4) | 2013-2015 | --- | --- | X | X |
6M Series | 2013 and newer | --- | --- | X | X |
6J Series | 2018 and newer | --- | --- | X | X |
5R Series | 2019 and newer | --- | --- | X | X |
*NOTE: For latest Precision Ag functionality, update machines equipped from the factory with v1 processor to v2.
John Deere Nutrient Applicators
John Deere Nutrient Applicators |
Model year | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | ||
F4365 High-Capacity Nutrient Applicator | 2017 and newer | X | --- | --- | --- |
John Deere Self-Propelled Sprayers
John Deere self- propelled sprayers |
Model year | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | ||
4 Series Sprayers | 2018 and newer | X | --- | --- | --- |
4 Series Sprayers | 2013 - 2017 | --- | --- | X** | --- |
4940 | 2012 - 2014 | --- | --- | X** | --- |
4630 | 2008 and newer | --- | --- | X** | --- |
4730 | 2008 and newer | --- | --- | X** | --- |
4830 | 2008 - 2014 | --- | --- | X** | --- |
4930 | 2008 - 2013 (SN 4000+) | --- | --- | X** | --- |
Hagie© sprayers | 2014 and newer | Compatible with GreenStar© 3 2630 Displays and 4640 Universal Displays* |
*NOTE: When using the 4640 Universal Display on a Hagie Sprayer, additional mounting and harnessing may be required.
NOTE: Current John Deere/Hagie field kits only offer GreenStar 3 2630 Display parts.
NOTE: AutoTrac© Vision/AutoTrac RowSense and multi-rank section control are not supported on Hagie at this time.
NOTE: VIN detection on Hagie Sprayers is only supported on model year 2019 and newer machines.
**NOTE: The 4640 Universal Display will replace the GreenStar 3 2630 Display on the armrest. Dual display with the GreenStar 3 2630 Display is not supported with sprayers. Adding the 4640 Universal Display will disable the assignable buttons located on the sprayer armrest.
John Deere Self-Propelled Forage Harvesters (SPFH)
John Deere Self-Propelled |
Model year | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | ||
9000 Series SPFH | 2019 and newer | --- | --- | X | --- |
8000 Series SPFH | 2015 and newer | --- | --- | X | --- |
John Deere Combines
John Deere combines | Model year | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | ||
S700 Series | 2018 and newer | X | --- | --- | --- |
S430 and S440 | 2017 and newer | X | --- | --- | --- |
S600 Series | 2012 - 2017 | --- | --- | X* | X* |
S540 and S550 Series | 2012 and newer | --- | --- | X* | X* |
T-Series | 2012 and current | --- | --- | X* | X* |
70 Series | 2008 - 2013 | --- | --- | X* | X* |
NOTE: Competitive equipment may be compatible with 4640 Universal Display and 4240 Universal Display. For additional compatibility information, contact a John Deere dealer.
*NOTE: When adding the 4640 Universal Display to a John Deere combine, it will only be compatible as a cornerpost precision ag display.
John Deere Cotton Harvesters
John Deere Cotton Harvesters |
Model year | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | ||
CP690 | 2015 and newer | --- | --- | X | --- |
CS690 | 2015 and newer | --- | --- | X | --- |
NOTE: Update cab controller software to the latest version on model year 2017 and newer cotton harvesters to use Harvest Identification, Cotton Pro.
John Deere planters
SeedStar© 4HP planters are only compatible with 4600 CommandCenter displays with a version 2 (v2) processor and 4640 Universal Displays. Displays should be running Generation 4 OS software version 10.10.404-390 or newer and the most current version of tractor applications to be compatible with SeedStar 4HP planter applications. Additionally, dual-display mode is available for use with SeedStar 4HP planter applications, along with Generation 4 Extended Monitor. SeedStar 4HP planters are compatible with no more than two GreenStar Rate Controllers.
The SeedStar 2 configuration below is available only on factory-installed model year 2011 and newer planters and may be field-installed on model year 2009 and 2010 planters. Green PM/PA controllers (factory-installed on model year 2009 and 2010 planters) are not supported with a Generation 4 display.
A Service ADVISOR© tool (available at a John Deere dealer) is needed to update SeedStar 2, SeedStar XP, and SeedStar 3 HP software. Documentation is not supported when using a rate controller to control row clutches on a John Deere planter.
John Deere planters | Control unit name | Software version (or newer) | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240* | |||
SeedStar 2 |
Black PM1 | 22.0 | X | X | X | X |
Black PA1, (if available PA 2) | 22.0 | X | X | X | X | |
Green PM1 | 10.11 | --- | --- | --- | --- | |
Green PA1 (if available PA 2) | 10.11 | --- | --- | --- | --- | |
SeedStar XP |
Black PM1 | 22.0 | X | X | X | X |
Black PA1, (if available PA 2) | 22.0 | X | X | X | X | |
PM2 | 7.0 | X | X | X | X | |
SeedStar 3 HP |
Planter Main A (PCMA) | 6.0 | X | X | X | X |
Planter Main B (PCMB or MMC) | 8.0 | X | X | X | X | |
Row-unit Controller (RUC) | 2.0 | X | X | X | X | |
EPG | 3.0 | X | X | X | X | |
SeedStar 4HP |
Planter Apps | 10.4.332-12 | X | --- | X | --- |
Planter Main A (PMCA) | 6.0 | X | --- | X | --- | |
Planter Main B (PMCB or MMC) | 8.0 | X | --- | X | --- | |
Row-unit Controller (RUC) | 4.0 | X | --- | X | --- | |
Electrical Power Generation (EPG) | 5.0 | X | --- | X | --- | |
Electrical Power Module, 2 (PC2) | 3.0 | X | --- | X | --- | |
ExactRate© liquid fertilizer system | Master Nozzle Control Unit (MNC) | 1.0 | X | --- | X | --- |
Spray Rate Control Unit (SRC) | 1.0 | X | --- | X | --- | |
Liquid Blockage Controller (LBC) | 1.0 | X | --- | X | --- | |
Nozzle Control Unit (NZC) | 6.04 | X | --- | X | --- | |
ExactRate app | 10.1.269-41 | X | --- | X | --- |
*NOTE: For implements requiring ground speed input (radar), utilizing a 4240 Universal Display may require an additional 4240 Radar speed kit.
John Deere Air Seeders
The C650 and C850 Air Carts and N500C Seeder require a 4600/4200 CommandCenter Display or a 4640/4240 Universal Display. GreenStar 3 2630 monitors are not supported. Additionally, tow-behind C850 Air Carts are compatible with AutoTrac Implement Guidance (passive) with software update 18-2 and newer.
John Deere Air Seeder | Model year/control unit name | Software version (or newer) | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240* | |||
C650 Air Cart |
Cart Master Controller (CMC) | 1.0 | X | X | X | X |
Mini Tank Controller (TCX) | 1.0 | X | X | X | X | |
Front, Middle, Rear Tank Controller (TCU) | 1.0 | X | X | X | X | |
C850 Air Cart | Cart Master Controller (CMC) | 13 | X | X | X | X |
Mini Tank Controller (TCX) | 6 | X | X | X | X | |
Front, Middle, Rear Tank Controller (TCU) | 6 | X | X | X | X | |
1870 Seeding Tool - TruSet© system | 2017 and newer (IDC) | 5.0 | X | X | X | X |
1870 Seeding Tool - RelativeFlow© blockage sensors | 2017 and newer (BMU) | 5.0 | X | X | X | X |
1910 Air Cart - ground drive | 2009 and newer | 3.0 | X | X | X | X |
1910 Air Cart - hydraulic drive |
2013 and newer | 9.0 | X | X | X | X |
Seeding tools with air-run blockage - primary blockage |
2009 and newer (BMU) | 12.0 | X | X | X | X |
Seeding tools with air-run blockage - air-run blockage | 2009 and newer (BMU) | 12.0 | X | X | X | X |
Member Module | 5.0 | X | X | X | X | |
1990 Central Commodity System (CCS©) |
2009 and newer (BMU) | 12.0 | X | X | X | X |
N500C Series | Seeder apps | 10.2.18-31 | X | --- | X | --- |
SMCA or SMC | 3.0 | X | --- | X | --- | |
SMCB or BMU | 3.0 | X | --- | X | --- | |
EPG | 3.0 | X | --- | X | --- |
*NOTE: For implements requiring ground speed input (radar), utilizing a 4240 Universal Display may require an additional 4240 Radar speed kit.
John Deere Tillage
John Deere Tillage | Control unit name | Software version (or newer) | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | |||
AccuDepth© cultivator | Implement Depth Control (IDC) | 11 | X | X | X | X |
2730 with TruSet |
Tillage Controller 1 (TC1) | 2.66K9 | X | X | X | X |
2230 with TruSet | Tillage Controller 1 (TC1) | 2.75K6 | X | X | X | X |
2330 with TruSet | Tillage Controller 1 (TC1) | 2.35K6 | X | X | X | X |
2620/2630 with TruSet | Tillage Controller 1 (TC1) | 2.95K6 |
X | X | X | X |
2720 with TruSet | Tillage Controller 1 (TC1) | 2.24K6 | X | X | X | X |
2660VT with TruSet | Tillage Controller 1 (TC1) | 3.03K12 | X | X | X | X |
2430 with TruSet | Tillage Controller 1 (TC1) | 2.14K4 | X | X | X | X |
2510H with TruSet | Tillage Controller 1 (TC1) | 2.85K5 | X | X | X | X |
*NOTE: For implements requiring ground speed input (radar), utilizing a 4240 Universal Display may require an additional 4240 Radar speed kit.
John Deere Round Balers
John Deere Round Balers | Control unit name | Software version (or newer) | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | |||
0 Series | Baler Automation | 10.07 | X | X | X | X |
9 Series Premium |
Baler Automation | 7.16 | X | X | X | X |
V451R/V461R | Baler Automation | 11.5 | X | X | X | X |
John Deere Large Square Balers
John Deere Large Square Balers Including Harvest Tec applicator and PhiBer accumulator |
Control unit name | Software version (or newer) | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | |||
0 Series | Gen 4 VT | 3.04 | X | X | X | X |
1 Series |
Gen 4 VT | 5.07 | X | X | X | X |
John Deere control units | Control unit name | Software version (or newer) | CommandCenter | Universal Display | ||
4600 v2 | 4200 | 4640 | 4240 | |||
*StarFire 6000 Receiver | --- | 4.30F | X | X | X | X |
StarFire 6000 Integrated Receiver | --- | 4.30F | X | X | X | X |
StarFire 3000 Receiver | --- | 2.70A | X | X | X | X |
*Modular Telematics Gateways (MTG) - 3G | --- | 21.03 | X | X | X | X |
*MTG - 4G | --- | 27.01.541 | X | X | X | X |
GreenStar Rate Controller | --- | 3.70K | X | X | X | X |
GreenStar Rate Controller Dry | --- | 2.11A | X | X | X | X |
*John Deere Rate Controller 2000 | --- | 1.13A | X | X | X | X |
*AutoTrac Universal 200 | --- | 2.30A | --- | --- | X | X |
*AutoTrac Universal 300 | --- | 3.23G | --- | --- | X | X |
AutoTrac Controller 250 | --- | 11933B | --- | --- | X | X |
*AutoTrac Controller - Deere | --- | 1.11B | --- | --- | X | X |
AutoTrac Controller - Raven | --- | 10.13.909-158 | --- | --- | X | X |
AutoTrac Controller - Reichhardt® | --- | SW 1.3 | --- | --- | X | X |
AutoTrac RowSense | RG3 | AKK15783F | X | --- | X | --- |
AutoTrac Vision | VGC | 4.01V | X | --- | X | --- |
AutoTrac Turn Automation | --- | 19-2 | X | --- | X | --- |
AutoTrac Implement Guidance | --- | 19-2 | X | --- | X | --- |
Active Implement Guidance (VT) | Application Controller 1100 | 2.71Z | X | X* | X | X* |
Application Controller 1100 (S.N. PCXL01C201000-) | 3.11A | X | X* | X | X* | |
iGrade© | Application 1100 | 2.71Z | X | X | X | X |
Application Controller 1100 (S.N. PCXL01C201000-) | 3.11A | X | X | X | X | |
Distance Trip | Application 1100 | 2.71Z | X* | X | X | X |
Application Controller 1100 (S.N. PCXL01C201000-) | 3.11A | X* | X | X | X | |
Yield Documentation, Specialty Crop | Application Controller 1120 | 1.51Y | X | X | X | X |
Application Controller 1120 (S.N. PCXL02C201000-) | 3.11A | X | X | X | X | |
Mobile Weather | Application Controller 1120 | 1.51Y | X | X* | X | X* |
Application Controller 1120 (S.N. PCXL02C201000-) | 3.11A | X | X* | X | X* | |
Harvest Identification, Cotton | Application Controller 1120 | 1.51Y | --- | --- | X | --- |
Application Controller 1120 (S.N. PCXL02C201000-) | 3.11A | --- | --- | X | --- | |
Gen 4 Extended Monitor | X | --- | X | --- | ||
Wireless Data Server | Wireless Data Server | 1.591.2 (Planting) |
X | --- | X | --- |
Mobile Data Transfer | MyTransfer© app | 3.8.6 (iOS®) |
X | X | X | X |
Connect Mobile app | Connect Mobile app | 8.4.0 or newer | X | --- | X | --- |
Connect Mobile server | Connect Mobile server | 2.3.101-1 | X | --- | --- | --- |
Manure Constituent Sensing | Manure Controller | 19.06 | X | --- | X | --- |
*NOTE: See additional information below.
StarFire Receivers
StarFire Receivers can be updated in the following ways:
Additionally, StarFire iTC Receivers are no longer supported with software update 2017-1 and newer software. StarFire 6000 Receivers require software version 3.80F or higher when used with AutoTrac Implement Guidance.
John Deere Operations Center
To use RDA on a Generation 4 CommandCenter Display with a GreenStar 3 2630 Display connected in the same machine, GreenStar 3 2630 software version 3.22.1095 (SU2014-1) or higher is required (for 4600 CommandCenter Display and 4640 Universal Display only).
GreenStar Rate Controller and GreenStar Rate Controller Dry
GreenStar Rate Controller Dry is supported with display software update 2017-2 and newer. The 4600 and 4200 CommandCenter Displays and 4640 and 4240 Universal Displays support documentation and section control of up to five GreenStar Rate Controller units.
To update the GreenStar Rate Controller and GreenStar Rate Controller Dry, utilize a Generation 4 Display USB port. John Deere dealers can also utilize Service ADVISOR. GDC 2.11A was the last software version available through Software Manager. GDC 2.20A has been available since spring 2015 and contains diagnostic language updates. This software can only be obtained through Service ADVISOR.
John Deere Rate Controller 2000
The Generation 4 Displays and John Deere Rate Controller 2000 can support documentation and control up to five operations. ISO controllers such as SeedStar or TruSet can be used alongside a John Deere Rate Controller 2000 that is documenting additional operations. The John Deere Rate Controller 2000 will not control the planter clutches or half-, third-, or quarter-width disconnects on a John Deere planter.
AutoTrac© Vision
AutoTrac Vision Guidance Camera 19-1 software 4.01V is only compatible with RowGuidance 3 Controller software AKK15783F and GreenStar 3 2630 17-1 software 3.34.1345 or newer and Generation 4 18-1 software 10.10.404-345 or newer.
AutoTrac Universal 200, AutoTrac Universal 300, and AutoTrac Controller
AutoTrac Universal 200, AutoTrac Universal 300, and AutoTrac Controllers are for use with the 4640 Universal Display and 4240 Universal Dis
Machines must be GreenStar™ ready to be compatible with the AutoTrac machine kits. AutoTrac machine kits include the appropriate machine steering controller when necessary and AutoTrac-ready accessories. Display, receiver, and software to complete system sold separately.
Machines must be GreenStar™ ready to be compatible with the AutoTrac machine kits. AutoTrac machine kits include the appropriate machine steering controller when necessary and AutoTrac-ready accessories. Display, receiver, and software to complete system sold separately.
AutoTrac field-installed kits are now available for 6105R, 6115R, 6125R, 6140R, or 6150R MFWD Tractors.
These field-installed kits are an integrated guidance solution for John Deere 6R MFWD Tractors and are compatible with the GreenStar™ 3 or GreenStar 2 system components.
These kits contain all of the required hydraulic components and harnesses for field installation.
GreenStar display options:
StarFire™ Receiver and signal options:
AutoTrac field-installed kits are now available for 6105R, 6115R, 6125R, 6140R, or 6150R MFWD Tractors.
These field-installed kits are an integrated guidance solution for John Deere 6R MFWD Tractors and are compatible with the GreenStar™ 3 or GreenStar 2 system components.
These kits contain all of the required hydraulic components and harnesses for field installation.
GreenStar display options:
StarFire™ Receiver and signal options:
AutoTrac field-installed kits are now available for 6105R, 6115R, 6125R, 6140R, or 6150R MFWD Tractors.
These field-installed kits are an integrated guidance solution for John Deere 6R MFWD Tractors and are compatible with the GreenStar™ 3 or GreenStar 2 system components.
These kits contain all of the required hydraulic components and harnesses for field installation.
GreenStar display options:
StarFire™ Receiver and signal options:
AutoTrac field-installed kits are now available for 6105R, 6115R, 6125R, 6140R, or 6150R MFWD Tractors.
These field-installed kits are an integrated guidance solution for John Deere 6R MFWD Tractors and are compatible with the GreenStar™ 3 or GreenStar 2 system components.
These kits contain all of the required hydraulic components and harnesses for field installation.
GreenStar display options:
StarFire™ Receiver and signal options:
AutoTrac field-installed kits are now available for 6210R, 6190R, and 6170R MFWD Tractors.
These field-installed kits are an integrated guidance solution for John Deere 6R MFWD Tractors.
All required hydraulic components and harnesses for field installation are contained in these kits.
GreenStar™ display options:
StarFire™ Receiver and signal options:
The AutoTrac system reduces overlap, saving time, fuel, and labor costs. Whether breaking stubble with tillage equipment, planting or seeding, spraying or fertilizing, it reduces implement overlap by up to 90 percent. It also provides faster headland turns because the AutoTrac system takes the guesswork out of the return path.
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
When paired with a StarFire™ receiver and GreenStar™ display, the integrated AutoTrac™ machine kit completes the components that automatically steer the machine. This kit is tied directly into the steering system on the machine and, therefore, provides optimum accuracy. The steering kit components cannot be moved across machine platforms.
Key features of the integrated AutoTrac steering kit:
AutoTrac™ is an assisted hands-free steering system that automatically steers the machine through the fields. For some of the competitive sprayers, an AutoTrac Universal Hub will be required along with other attachments. For complete compatibility information, see the ATU look up tool.
AutoTrac™ is an assisted hands-free steering system that automatically steers the machine through the fields. For some of the competitive sprayers, an AutoTrac Universal Hub will be required along with other attachments. For complete compatibility information, see the ATU look up tool.
AutoTrac™ is an assisted hands-free steering system that automatically steers the machine through the fields. For some of the competitive sprayers, an AutoTrac Universal Hub will be required along with other attachments. For complete compatibility information, see the ATU look up tool.
Machine specific kits provide dealers with all of the hardware and harnessing to equip your 2410C or 2510H with dry applicator with AccuFlow Vortex Cooler minus:
The GreenStar™ Lightbar is a simple, economical Parallel Tracking™ display.
The 27 tracking indicator light-emitting diodes (LED) tell the operator how the machine is tracking in relation to the desired guidance line.
The operator steers the vehicle back to the guidance line.
GreenStar Lightbar can be run as a stand-alone unit or as a companion to either an Original GreenStar Display or GreenStar 2 (GS2) 2600, GreenStar 2 1800, or GreenStar 3 2630 Display.
NOTE: The GreenStar Lightbar cannot be power washed.
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
First introduced in 1995, Combine Yield Monitoring and Combine Yield Mapping were John Deere’s first precision farming products. It is capable of monitoring or mapping yield and moisture on many of the older John Deere combines as field-installed attachments.
Harvest Monitor™ and Harvest Doc™ – 9060 Series Combines
*Harvest Monitor and Harvest Doc is retrofittable to 50 Series Combines
Functionality includes multi-client functionality, boundary recording, and weather and field condition recording as well as compatibility to GreenStar™ guidance products.
Harvest Monitor enables the operator to view yield and moisture while harvesting. It consists of the following components:
Harvest Doc enables the operator to record yield and moisture with GPS and later load the information into desktop software as maps and reports. To upgrade from Harvest Monitor to Harvest Doc, the following additional components are necessary:
StarFire™ Receiver
PF80762 - Storage case for original GreenStar™ common components