John Deere 459E

Feature Overview
John Deere 459E
  • Two models: twine or netwrap
  • Makes tight and dense 4’ x 5’ bales
  • Adjustable hitch to match wide array of tractor drawbar heights
Feature Overview
John Deere 459E
  • Two models: twine or netwrap
  • Makes tight and dense 4’ x 5’ bales
  • Adjustable hitch to match wide array of tractor drawbar heights
Features

Regular pickup offers large feed opening and low-profile, mid-mounted pickup

Regular pickup on 459E Baler with converging wheelsRegular pickup on 459E Baler with converging wheels
#

Mounted in front of the baler wheels and directly below the bale chamber, the pickup hugs the ground for clean crop retrieval. Hay movement is minimized.

  • V-belt driven
  • 449, 459E, and 459 Baler pickups are 116.6 cm (45.9 in.) wide
  • 559 and 569 Baler pickups are 156 cm (61.4 in.) wide
  • Large reel shaft and reel bearing

The small-diameter, low-profile pickup allows for good ground gauging and clean crop retrieval.

  • Handles large, heavy windrows of hay and high-moisture crops
  • Feeds hay directly to the forming chamber to reduce crop loss
  • Low-profile pickup minimizes hay lift to reduce chaffing to retain hay quality

Side flares prevent hay from blowing off the pickup ends and reduce hay loss.

The closely spaced pickup teeth extend to the baler side sheets to help build straight-edged bales.
Standard on regular and MegaTooth™ pickups, compressor rods are contoured to control hay over the pickup radius for positive feeding. The compressor rack can be adjusted upward or downward to match the volume of material in windrow and can be easily removed to match crop conditions.

Adjustable crank handleAdjustable crank handle
#

The adjusting crank positions the pickup to the desired operating height to match crop or field conditions.

An optional hydraulic pickup lift cylinder is available as an attachment.

  • Makes raising for transport or clearing obstructions easy
  • Crank handle serves as a down stop
  • Adapts to regular, MegaTooth and MegaWide™ Plus pickups
  • Hydraulic pickup lift comes standard on premium machines

Staggered beltsStaggered belts
#

John Deere's 17.8-cm (7-in.) wide diamond-tread design ensures fast bale starts and grips the bale to prevent slippage and reduce chaffing. The treads are self-cleaning to reduce carryover.

The belts are staggered to reduce the loss of fine material and are closely spaced to contain the hay for fast, easy starts.

The belts enclose 91 percent of the bale width to reduce the loss of fine material and retain hay quality.

The staggered belt roll design enables any loose hay under or behind the belts to be returned to the pickup and into the baler.

This design helps to prevent buildup at the front of the baler, which could cause hay loss and belt or splice damage.

Three-ply beltsThree-ply belts
#

The 449 and 459E Balers use three-ply belts. The belts are constructed of three-ply nylon-polyester combination:

  • They have the strength to handle heavy-shock loads and help to maintain consistent belt length.
  • Polyester is used for increased strength and reduced belt stretch.
Extra-service-life belt splices
Extra-service-life splicesExtra-service-life splices
#

The 449 and 459E Balers use extra-service-life, rectangular, wire-belt splices:

  • Flat surface reduces wear on the splice as the belt travels around the rolls.
  • Strong hook shape increases the splice life as the belt flexes.

The material thickness and bend radius resist the opening of hook points and reduce metal fatigue.


Bale-starting diagramBale-starting diagram
#

As the hay enters the forming chamber from the pickup, belts turn the hay immediately to form a tight, dense core.
 
Incoming hay then feeds between the bale and the lower-gate roll. Hay is tightly compressed into smooth, dense layers as it enters the bale.
 
Chaffing is greatly reduced to prevent loss and retain hay quality in the bale.

Full-sized bale in bale chamberFull-sized bale in bale chamber
#

The idler arm rises with bale growth, forcing oil from the hydraulic cylinder through a pressure-relief valve:

  • Maintains uniform bale density throughout the bale-forming process

Side view of adjustable hitchSide view of adjustable hitch
Front view of adjustable hitchFront view of adjustable hitch

The 9 Series Round Balers come standard with an adjustable hitch. This feature allows the hitch height to be adjusted to optimize crop-feeding performance. Due to the wide array of tractor tire sizes and drawbar heights, hitch adjustment may be necessary to get the proper feed opening of the baler. The adjustable hitch eliminates the need for the 51-mm (2-in.) thick tractor drawbar kit (AE57344) because it has a wider opening.

Benefits of the adjustable hitch:

  • Ability to match baler to numerous tire sizes
  • Allows for drawbar height to fall within 330 mm to 559 mm (13 in. to 22 in.) from top of drawbar to the ground
  • Eliminates narrow feed opening on baler which can cause plugging
  • Allows pickup head to follow terrain without missing crop

All eight bolts must be used when adjusting the hitch. There are four different positions as shown below:

Position 1 (top) - Regular and MegaTooth© pickupsPosition 1 (top) - Regular and MegaTooth© pickups
Position 2Position 2
Position 3 (factory setting) - MegaWide© Plus pickupsPosition 3 (factory setting) - MegaWide© Plus pickups
Position 4 (bottom)Position 4 (bottom)

Also standard on all 9 Series Round Balers except the 459E is the drawbar flap. This helps to eliminate hay from getting caught on the hitch of the baler. The drawbar flap is designed to allow the operator to remove or attach the flap without having to unhook the baler from the tractor.

Drawbar flapDrawbar flap
Drawbar flap installed on balerDrawbar flap installed on baler

Larger shafts ™ 8 Series, 9 Series, 9 Series PremiumLarger shafts ™ 8 Series, 9 Series, 9 Series Premium
#

The 9 Series Round Balers have increased their durability by increasing the shafts and bearings on the top and bottom rolls of the baler. The size of the shafts and bearings are listed below:

  • 8 Series - 31.8-mm (1.25-in.) shaft and 90-mm (3.5-in.) outside diameter (OD) bearing (this bearing requires a quill assembly to fit in the roll)
  • 9 Series - 38.1-mm (1.5-in.) shaft and 130-mm (5.1-in.) OD bearing (this bearing does not require a quill assembly to fit in the roll)
  • 9 Series Premium - 44.5-mm (1.75-in.) shaft and 130-mm (5.1-in.) OD bearing

The #9 and #11 rolls receive the most wear and stress since they have the most surface area contact with the belts. The lower gate roll also carries the weight of the bale. By increasing the shaft size, strength is added to the baler. The larger bearings will run cooler, therefore, increasing the life of the bearings.

Diagram of rolls on balerDiagram of rolls on baler

Audible alarm
BaleTrak Pro monitor-controllerBaleTrak Pro monitor-controller
#

The BaleTrak Pro monitor-controller is included with the automatic electric tie option and the Edge-to-Edge option on the 459E. The monitor sounds an alarm for near-full, full, and oversized bales.

  • Monitor beeps once to notify the operator to even-up the bale prior to reaching the desired size.
  • Monitor beeps twice when the bale reaches the desired size.

    • If the operator continues to feed hay into the baler, the monitor will sound continuously to warn of an oversized bale.

  • Bale shape bars are not available on the 449 or 459E Round Balers. The 449 and 459E Round Balers allow for adjustment of twine settings from the cab by using the BaleTrak Pro Monitor.
  • The number of wraps on the Edge-to-Edge netwrap option on the 459E can be set with the BaleTrak Pro.

The audible level of the monitor can be adjusted.


Specs
Bale
Size Diameter
89 to 152 cm
35 to 60 in.
Width
117 cm
46 in.
Weight Full-size bale in dry crop
454 kg
1,000 lb
Bale forming
Forming chamber Variable
Belts-other Number
6 belts
Strength
3-ply
Width
17.8 cm
7 in.
Length, regular
Two: 1,171 cm
461 in.
Length, staggered
Four: 1,185 cm
467 in.
Fabric
Nylon polyester combination
Texture
Diamond tread
Enclosed % of bale surface 91 percent
Belt splices Extra service life
Density control Hydraulic, isolated tractor
Baler
Base weight 1,701 kg
3,750 lb
Length Gate closed
361 cm
142 in.
Gate open
455 cm
179 in.
Height Gate closed
260 cm
102 in.
Gate open
325 cm
128 in.
Weight*
Driveline
Type Constant velocity, category 3
Drive protection Shearbolt
PTO speed 540 rpm
PTO lockback collar on tractor hookup Yes
Mega tooth pickup
Width
Monitor
Monitor console for tractor BaleTrak Pro
Gate closed Symbol on monitor
Bale size Digital display
Near full bale Audible
Full bale Audible
Twine arm position Indicator Mechanical indicator
Auto wrap Activates when bale reaches preset size
Oversize bale Audible and Mechanical
Regular pickup
Drive Roller chain with V-belt
Bars 4
Number of teeth 72
Tooth spacing 6.6 cm
2.6 in.
Lift control Crank
Gauge wheels Optional
Stripper diameter 25.4 cm
10 in.
Tire size
Standard 11L-14, 8-ply
Tractor Requirements
Minimum PTO 42 kW
55 hp
Wrapping system
Control Automatic to preset to bale size
Twine arms Two
Twine ball capacity Four
*Manufacturer's suggested price. MSRP may be different in California. Taxes, freight, setup, and delivery not included. Optional accessories and attachments not included. Equipment, models and prices may vary by dealer. Product options and accessories may not be available in all regions. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s website for additional information. Offers valid in the United States. Prices in U.S. dollars.
Belle Glade

2017 Northwest 16th Street
Belle Glade, FL 33430
561-996-6531

Map & Hours
Boynton Beach

1335 Neptune Dr
Boynton Beach, FL 33426
561-732-8905

Map & Hours
Brooksville

22255 Cortez Blvd
Brooksville, FL 34601
352-573-2720

Map & Hours
Fort Myers

9501 FL-82
Fort Myers, FL 33905
239-332-5045

Map & Hours
Fort Pierce

6150 Orange Ave
Fort Pierce, FL 34947
772-461-5568

Map & Hours
Immokalee

775 E Main St
Immokalee, FL 34142
239-657-4413

Map & Hours
Largo

6785 114th Ave
Largo, FL 33773
727-828-8200

Map & Hours
Leesburg

1800 US-441
Leesburg, FL 34748
352-315-1016

Map & Hours
Loxahatchee

13295 Southern Blvd
Loxahatchee, FL 33470
561-784-4000

Map & Hours
Naples

1945 Pine Ridge Rd
Naples, FL 34109
239-260-8800

Map & Hours
North Port

2825 Commerce Parkway
North Port, FL 34289
941-924-9709

Map & Hours
Odessa

2240 Success Dr
Odessa, FL 33556
727-842-8618

Map & Hours
Okeechobee

820 US-98
Okeechobee, FL 34972
863-763-1921

Map & Hours
Orlando

12049 S Orange Blossom Trail
Orlando, FL 32837
407-240-1023

Map & Hours
Palmetto

906 US-301
Palmetto, FL 34221
941-722-3281

Map & Hours
Plant City

2805 West, FL-60
Plant City, FL 33567
813-737-1660

Map & Hours
St Cloud

117 13th St
St Cloud, FL 34769
321-209-4888

Map & Hours
©2021 EFE, Inc. All Rights Reserved | Designed In-House by Everglades Equipment Group