John Deere 131

Feature Overview
John Deere 131
  • High-speed rotary disk cutterbar for cutting in tough conditions
  • Windrowing solutions to match your needs
  • Use front hitch for maximum productivity
Feature Overview
John Deere 131
  • High-speed rotary disk cutterbar for cutting in tough conditions
  • Windrowing solutions to match your needs
  • Use front hitch for maximum productivity
We are here to help
Features

Windrowing solutions to match your needs

Adjustable forming shields (curtain moved for visibility) Adjustable forming shields (curtain moved for visibility)
Windrows Windrows

The desired swath width can easily be obtained by loosening the handle on each side and moving the adjustable swath deflectors to the desired position. Swath width is adjustable from 1.4 m to 2.0 m (4 ft, 7 in. to 6 ft, 6 in.) on the 131 Front-Mounted Mower-Conditioner.

 

The available room for a windrow is a function of wheel spacing and tire width. The windrow width of the 131 Front-Mounted Mower-Conditioner may be narrower than the windrows from a 388 Twin Rear-Mounted Mower-Conditioner if the forming shields are adjusted so the tractor does not drive on the windrow that is produced.

 

A wide spread kit is available as a field-installed bundle. This kit is composed of vanes installed under the conditioning hood. The crop flow is spread to approximately the machine working width and offset about 400 mm (15.75 in.) on the left-hand side. This allows a clean separation between the uncut crop and spread crop.


131 Mower-Conditioner cutterbar (shields raised for visibility) 131 Mower-Conditioner cutterbar (shields raised for visibility)
#

Power is transmitted from the 1000-rpm PTO on the front of tractor through gearcases to the cutterbar.

  • Standard position for main gearcase utilizes clockwise (as determined by direction of travel) rotation of the front PTO.
    • Gearcase can be reversed for use with tractors with a counterclockwise (as determined by direction of travel) front PTO
  • Cutterbar is protected by a slip clutch and overrunning clutch
  • Cutterbar is securely mounted within the frame for strength and durability

Power is transmitted to the rotary disks through fully enclosed gears, running in oil, for quiet, smooth, reliable operation

  • The high-speed rotary disks cut in the toughest conditions. The disks rotate at 2986 rpm.
  • Low-profile design enables cutting close to the ground at a flat angle helping prevent damage to the disks and knives.
  • Pinion gear is easily removed from the top of the cutterbar for service
    • Idler gears can be removed from access area after removal of pinion gear
Turnbuckle adjustment Turnbuckle adjustment
#

Cutting height is adjusted by changing the turnbuckle on the front hitch. Cutting range is from 30 mm to 80 mm (1.2 in. to 3.15 in.).


Impeller conditioner Impeller conditioner
#

The mower-conditioner is equipped with 54 free-swinging, steel impeller tines. This John Deere conditioner provides excellent conditioning performance and fluffy windrows. 

Impeller conditioning is standard equipment on all John Deere mower-conditioners.

 

Proper conditioning in a wide range of crops can be achieved when the conditioner is properly adjusted.

 

The impeller conditioner works well in legumes, especially alfalfa and most all-grass crops. Impeller conditioners are not recommended for thick-stemmed or cane-type crops, such as sudan or sudex, or crops over 5-ft tall.

How an impeller conditioner works:
Impeller conditioning Impeller conditioning
#
  1. As hay is cut by rotating knives, tines (2) pick up the plants and carry them through the machine: Tines are free swinging to reduce damage to the conditioner if rocks or other solid objects are struck. 
  2. As the plant passes through, it rubs against the conditioning hood (1) and other plants: Scuffing action removes the waxy surface from the stem of the plant to allow faster evaporation of moisture.
  3. The pivot point for the conditioning hood is also adjustable to provide a wider range of conditioning intensity.
Adjusting impeller speed (shield removed for illustration) Adjusting impeller speed (shield removed for illustration)
#

The speed at which the tines rotate will also affect the degree of conditioning. Two impeller speeds can be achieved by interchanging the upper sheave and the lower sheave.

  • With the sheaves in the position shown, the impeller turns at 888 rpm; this is ideal for grasses.
  • If the sheaves are reversed, the impeller turns at 615 rpm; this is ideal for legume crops. 

Tractor hookup
8R Tractor front hitch 8R Tractor front hitch
#

The Model 131 Front-Mounted Mower-Conditioner is used to maximize the potential of the 7R or 8R Tractor equipped with a front PTO. This 1000-rpm mower-conditioner can be combined with the following 1000-rpm mower-conditioners to increase productivity:

  • Side-pull mower-conditioner
  • Center-pivot mower-conditioner
  • Twin rear-mounted mower-conditioner

Unmatched productivity is gained with cutting widths up to nearly thirty feet in one pass along with a narrow transport width.

The A-frame adapter enables quick and easy installation of the 131 Front-Mounted Mower-Conditioner. The adapter attaches to the tractor’s front 3-point hitch and locks into the mating headstock that is part of the mower-conditioner.

  • Enables easy attaching/detaching of front-mounted mower-conditioner
  • Mounting position of headstock is adjustable to assure proper clearance for the forming shields

Down stop chains are include for use with tractors, such as the 8R, without front hitch position sensing. A front chain support kit (RE327692) is required to connect the down stop chains on an 8R Tractor.

 

The 7R Tractors are equipped with position sensing that has the ability to establish front hitch set points from the CommandCenter©. Position sensing will maintain the height of the hitch arms based on the set point.

 

The front chain support kit (RE327692) is not required for 7R Tractors, but damage to the front PTO driveshaft can occur if the front hitch positioning is not set correctly, or if the set point is manually overridden.

Hydraulic cylinders are used to raise and lower the cutting platform when crossing headlands.

  • Front tractor hitch is not used to raise and lower the cutting platform
  • Uses single-acting selective control valve (SCV) to raise platform.
  • Lift cylinder operation must be independent of the front hitch operation.

Specs
Conditioner
Impeller Width
264 cm
104 in.
Number of V-tines
54
Number of speeds
Two
Drive
Belt and sheaves
Conditioner hood
Adjustable
Rolls



Cutterbar
Type Rotary
Cutting width 3.1 m
10.1 ft
Cutting height 30-80 cm
1.2-3.2 in.
Number of disks 8
Number of knives 16
Disk speed 2,986 rpm
Disk drive Gear
Lubrication GL-5 Gear Lubricant
Oil reservoir capacity 2.25 L
0.59 U.S. gal.
Cutterbar oil check Fill plug
Cutterbar angle Adjustable
Angle adjustment Tractor center link
Cutterbar protection Shear shaft
Dimensions
Overall width Transport
3.1 m
10.1 ft
Weight

With impeller conditioner
1,255 kg
2,766 lb
Overall length
Power requirements
PTO speed 1,000 rpm
HP 1000 rpm 1-3/8 in. PTO 75 kW
102 hp
HP 1000 rpm 1-3/4 in. PTO 75 kW
102 hp
Tractor hookup
Standard hitch Tractor front hitch
*Manufacturer's suggested price. MSRP may be different in California. Taxes, freight, setup, and delivery not included. Optional accessories and attachments not included. Equipment, models and prices may vary by dealer. Product options and accessories may not be available in all regions. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s website for additional information. Offers valid in the United States. Prices in U.S. dollars.
Belle Glade

2017 Northwest 16th Street
Belle Glade, FL 33430
561-996-6531

Map & Hours
Boynton Beach

1335 Neptune Dr
Boynton Beach, FL 33426
561-732-8905

Map & Hours
Brooksville

22255 Cortez Blvd
Brooksville, FL 34601
352-573-2720

Map & Hours
Fort Myers

9501 FL-82
Fort Myers, FL 33905
239-332-5045

Map & Hours
Fort Pierce

6150 Orange Ave
Fort Pierce, FL 34947
772-461-5568

Map & Hours
Immokalee

775 E Main St
Immokalee, FL 34142
239-657-4413

Map & Hours
Largo

6785 114th Ave
Largo, FL 33773
727-828-8200

Map & Hours
Leesburg

1800 US-441
Leesburg, FL 34748
352-315-1016

Map & Hours
Loxahatchee

13295 Southern Blvd
Loxahatchee, FL 33470
561-784-4000

Map & Hours
Naples

1945 Pine Ridge Rd
Naples, FL 34109
239-260-8800

Map & Hours
North Port

2825 Commerce Parkway
North Port, FL 34289
941-924-9709

Map & Hours
Odessa

2240 Success Dr
Odessa, FL 33556
727-842-8618

Map & Hours
Okeechobee

820 US-98
Okeechobee, FL 34972
863-763-1921

Map & Hours
Orlando

12049 S Orange Blossom Trail
Orlando, FL 32837
407-240-1023

Map & Hours
Palmetto

906 US-301
Palmetto, FL 34221
941-722-3281

Map & Hours
Plant City

2805 West, FL-60
Plant City, FL 33567
813-737-1660

Map & Hours
St Cloud

117 13th St
St Cloud, FL 34769
321-209-4888

Map & Hours
©2020 EFE, Inc. All Rights Reserved | Designed In-House by Everglades Equipment Group